KUDF204EPA00 KitchenAid Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Wendy from W LONG BRANCH, NJ
- Parts Used:
- EDR6D1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
I changed the filter
I changed the filter. With a wrench I turned the old filter counterclockwise to remove. I then proceeded to insert the new filter and turn it clockwise. That’s it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from Las Vegas, NV
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Leaking tray shorted heater
Removed the old ice maker and replaced with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Antioch, IL
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Water leaking out of Icemaker
I undid two top screws and one bottom screw. The tools came out of my cheapo walmart tool kit. I disconnected the power connector. I then put the new Icemaker in and waited for ICE. 12 hours later still no ice. I contacted Parts Select and before I knew it an new Icemaker was ordered and delivered to my doorstep. I received several emails to confirm the refund and re-billing of icemaker. I was absolutly astonished by how well they responded. I figured weeks after the first replacement came in DOA but two days later I had Ice and all was well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Metairie, LA
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Old ice maker was leaking water during initial fill cycle
Removed three srews holding the ice maker in place. Unplugged the wiring. Plugged in new ice maker wiring. Installed the new ice maker with the three screws. I left the old wiring in place. Works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Ocean Shores, WA
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Ice won't release from the mold
Lossen two screws at the top and remove one at the bottom and lift the unit off of the top screws, unplug the old unit and after cutting out the tray for the water fill spout plug the new one in. No problem .................
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mathew from cleveland hts., OH
- Parts Used:
- 4317943
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
would not make ice
remove the ice bucket support bracket and remove bottom screw from icemaker, loosing the two top screws and slide icemaker back enoughto unplug electric harness
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Greenwood, IN
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Stopped making ice.
Removed three screws and unpluged wiring. Replaced new unit by plugging in wire and replacing three screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Rockford, IL
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Ice maker would not stop making ice.
I viewed the video that was provided on partselect.com. The video was very instrumental in the removal and installation of the ice maker. I removed the old ice maker and installed the new ice marker, turn the water valve back on and had ice within 24 hours. When I reconnected the electrics and turned the water supply back on to the ice maker I thought it would fill with water right away, but it didn't. So I determined that the ice maker needed to run though a cycle, which took several hours, before it actually started making ice. With the video I was able to change the ice maker in less than a half an hour.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Clifton, NJ
- Parts Used:
- 4317943
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Replace Leaky Ice maker
Removing the hex screws from the existing unit was trouble until I found the screwdriver attachment to the hex wrench. The MOLEX type power connector was an exact match for what was on the unit, so the conversion cables were not needed. Unit worked fine. No more leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Kingsburg, CA
- Parts Used:
- 4317943
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Ice maker died
I took out the bottom locking screw and loosened the top two screws. I took the old icemaker out. I disconnected the wiring harness at the ice maker. I attached the new icemaker and mounted it in place. I didn't have to use any of the included wiring harnesses since the old one worked fine. I did use the old wire bale. I'm fairly ungifted in fixing things so I was amazed at how easy and inexpensive this was. The icemaker started up right away. The whole thing probably cost less that just the service call minimum would have been.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandford from South Toms River, NJ
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
ice maker stopped working
I ordered the replacement ice maker on a Saturday, received it on the next Tuesday, and in stalled it in a little over 15 minutes. Very quick, very easy. Partselect.com was easy to use and exceeded my expectations on every issue. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Sunrise, FL
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Stopped making ice cubes
Tested water valve by disconnecting power and adding 110VAC to valve to be certain the valve worked before ordering new ice maker. Rather than guessing on the part of the ice maker that was defective I ordered a new ice maker complete for a few doorars more and that fixed the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from Ames, IA
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Ice maker was flooding the freezer
After turning off the water to the fridge, I removed the 3 screws holding the icemaker, and unhooked the wire harness. I just reversed the process to reinstall and it took about 20 minutes, and we had a bin full of ice the next day.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Kuna, ID
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The icemaker stopped making ice.
I first removed the door, very easy to do, then removed one screw that held the icemaker in place. I then unplugged the electricity to the frig, slid the unit out and disconnected the electrical harness. Luckily the harness on the new icemaker matched up with the original plugin on the frig so it wasn't necessary to change the wiring on the new part. I simply slid the new icemaker in plugged it in put the retaining screw in, the door on, plugged the frig in and started makinmg ice. Couldn't have been easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Parker from Bangor, ME
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
icemaker unit leaked
followed instructions and replaced unit.
very easy and will roder again from this
very easy and will roder again from this
Was this instruction helpful to you?
Thank you for voting!