KUDF204EPA00 KitchenAid Refrigerator - Instructions

Removed one screw on cover covering wires on old ice maker,disconnected plug, removed ice maker, checked connector to make sure there was120vac, Power supply was good, installed new ice maker, connected plug. Works great.
Part to fix ice maker is very expensive, complete unit only $15 more and it has a one year warranty.

With a little investigation, I found that the ice tray had corroded, and the increased friction was keeping the ice from dumping out properly. It also had apparently damaged the gear motor, and the timing of the ice ejector was off. I went to the Part Select site and found that the icemaker specifically for my refrigerator was significantly more expensive than the universal Whirlpool replacement icemaker, but the two looked similar, so I ordered the universal replacement. When it arrived about 3 days later, I was able to easily remove the standard parts and replace them with the plastic parts and wire harness that were unique to my refrigerator. They fit perfectly, and I had the new icemaker installed in only about 20 minutes, including time spent to remove and replace the plastic parts

3 screws and plugged in the new ice maker. It was slightly difficult to unplug the old ice maker and place the plug in the new ice maker. Still really easy. New ice maker works great!

Replacing the ice maker is no big deal. Just take out the old one and replace it with the new one. The replacement, however, didn't work very well. Seemed like its timer was off, so it would dump ice cubes before they were completely frozen. So, we go shells of ice cubes. Not good. Called Parts Select, advised them of the problem, and they agreed to replace the part. Could not be happier with the customer service I received from this company.

It was very fast and easy. Two screws to take of the ice door cover. the ice maker itself just slid out and all I did was disconnnect the wiring harness. Unscrewed the plastic bottom case and screwed onto the new one. Attached the harness and slid it back in.

i can't believe it was that easy, just removed the screws, pulled elements out disconnected wires well it seemed to easy so had to read the directions or it would have took only 10 minutes. to do this job. thanks so much for your web sight, the repair man said it would probably be 200.00 or so

yea right 100.00 and its making all the ice we need thanks

joan mcquain

it was very very simple, it took only three screws
using socket set.
I removed the old one and put the new one in place , connect electric connection in 2 seconds snapping it toghether, that is all to it.
the hardest part is waiting on the ice to be made , which it took three to four hours for the first batch.
I am in the medical profession, IF I CAN do it , everyone CAN!!!!!!!!

First I unpluged the refriderator and removed the old ice maker. I then just simply installed the new ice maker. It was just that simple. The next morning I woke up with a full tray of ice.

I watched the recommended you tube video multiple times. I made sure to have the tools and towels ready. I shut off the water supply line, and capped it, removed the backing, and inspected the back. By following the video, the rest was easy. I recommend removing any built up dust and dirt while you have the front apart.

First I tried repairing the but that did not work, so I looked online and found partselect.com, put in my part number and wammo! There it was, the same exact water inlet line, and reasonably in-expensive. I ordered it and it got here pretty quick.

Followed video and had one problen, the metal pipe would not release as shown,so I used a hacksaw between the plastic and metal pipe, removing the metal pipe from inside as the video shows. Good instructions.

Followed instructions from online video. Used the opportunity to clean the freezer compartment really well. Also discovered that water solenoid valve was failing and have since replaced that also.

As directed in video clip, an excellent instruction video. Made for one of my quickest trouble free repairs in a long while.

New inlet valve. very easy. Part select was great. I first ordered a new ice maker, this did not fix the problem. Part select allowed me to return it and get the right part. The repair vidio was great.

After diagnosing the ice maker wasn't working, I got the model & serial number of the refrigerator. Picked the ice maker online by picture, that was a first. Three screws to take the old one out and replace the new. Written directions confirmed there is no manual cycle button on ice maker. Waited a couple hours and checked it, there was ice! Everybody was happy.