KFIS25XVMS9 KitchenAid Refrigerator - Instructions

Removed old gasket by carefully pulling it out of the retaining groove. Installed the new gasket starting the corners first and then seating the upper and lower straight portion gently in the retainer groove. Total time for installation was at most 5 minutes. After a week no ice or frost has been found along the bottom of door or freezer. Note: the new gasket came in a small box for shipping purposes and the new gasket was twisted in a v for this purpose. Upon arrival, I laid it out flat on table overnight so it could cool to room temperature and straighten. I would recomend this procedure for a perfect installation.

Replaced filter and the water started to flow like the Nile River and the ice maker came back to life.

Took out the old and installed the new.. The fit was perfect.

There was little or almost nothing to change out the End Cap, two screws on the End Cap and two screws on slide. It took longer to removed and replace the two drawers and shelve than it did to replace the End Cap. The part I ordered was exactly what I needed.

Unscrew filter. Screw on filter bypass

The repair was very simple, you just remove the existing part that is held in place by two holes in the lid and insert the new lid. very easy.

Replacing the part itself was easy, but getting the spring in position before installing the Yoke/Pad was a bit difficult. I had to insert the spring on the Yoke/Pad tab, then retract the spring (which was difficult) prior to putting the Yoke/Pad into place on the dispenser assembly. This requires force and would be very easy to bend or break the Yoke/Pad tab. I'm not sure if there is some trick to retract the spring and keep it retracted during the Yoke/Pad installation.

Remove rail and removed broken black plastic spring mechanism with new one and then replace rail.

For this repair, the following YouTube video was most helpful in showing how to remove the ice maker from the refrigerator model that I have: for some reason this site has deleted my video cite but it is the YouTube video cite that ends in 7HHH03SFdCA Next, because the electrical wiring harness part has changed since production, and the new ice maker part comes with two different harness' (you have to determine which one is most similar to the harness that you remove), take a lot of pictures of the old wiring harness before removing it. There are a lot of different wires that need to be reconnected. There was a prior post by "Greg from Aliso Viejo, CA" that I printed out and followed--that post was also very helpful.

Honestly, so simple . Removed the fruit / veggie drawers, glass shelf and the supports for that shelf. Couple of screws and nuts and it was off. As stated before... the most "thought goes into attaching the linkage for the temp adjustment on the right side . GREAT opportunity to CLEAN the up the fridge a bit!! Parts Select made this such a no brainer. Their Customer Service was really an added bonus!!

Layer it out for 24 hrs used hairdryer on med for the wrenkles.

Removed old ice maker by removing 3 screws, unplugged wiring harness. Replaced with new ice maker, placed three screws back to secure the ice maker, plugged wire harness back, and product is working well at this time.

Took out ice maker. Then unscrewed tray after opening old turn motor clock panel and carefully detaching wires from socket(s) where needed. Put in and screwed in new tray with the new motor clock. Replaced wires into new sockets. Put the whole maker back into place. Makes great ice.

Since it wasn't possible to squeeze the seal in between the door groove and the bar which closes the gap between the two doors, I cut the seal side in half and snaked it in from the top and the bottom. Since the cut is behind the bar when the door is closed there is no compromise in getting a good seal around the door. Note there was no apparent way to easily remove this bar.

Very easy. Just get hold of the gasket with your strong fingers and pull it out of the groove it is in. Clean the groove, I used Windex and paper towels. On the new gasket there are 2 wide areas on the vertical part. these must be facing toward you and on the handle side of the door. start at the tor center of the door and work the gasket in with your fingers outward to the corners then work on the bottom of the gasket in the same manner, then start on the vertical gaskets. when you think every thing is aligned take your thumbs and press very hard all around. You may have to repeat.