KSSO42QTX04 KitchenAid Refrigerator - Instructions

The emitter code: Hold the flap that covers the receiver. (On the left) If the emitter does not stay red, the emitter and receiver are defected.

Replaced the emitter and receiver board

Unplug the refrigerator:

I first removed the ice-maker service door by removing the 2 screws at the top. Next, I removed the 3 screws on the lift side that housed the receiver. It is close, so remove the 1 gold screws on the receiver. This will allow you to separate the switch without any damage. Plug the new receiver in and reverse the process. Put the gold screw in to secure the board. Replace the 3 screws back into the receiver panel.

Remove the 3 screws on the right side. The emitter has 2 gold screws. Remove them so I could separate the switch. Plug the new switch in and replace the 2 gold screws.
Place the 3 screws back into the right side panel.

This process took roughly 30 minutes. After assembly, the ice make was dropping ice in 30 minutes.

There are several large parts places in my area but I saved about $35 by ordering online.
I place my order on Friday morning and the part was in my hands Saturday @ 6: 30 PM the next day.




Oliver of Riverdale, Ga

System not cooling. removed back cover and notice fan not rotating. Looked up unit and found diagram. Ordered motor which was received in less than 5 business days.
Replacement was super easy. Just unscrewed from frame, pulled off fan, put fan on new motor and remounted back in frame. Took 10 minutes tops.

Removed the cover plates and unplugged bad boards. Hard to plug in boards after attached to cover plates. Plug in boards first then attach to mounts. Ice in 4 hours.

followed the video provided on website. repair was very simple / straight forward. Once emitter and receiver boards were replaced, issue with ice maker was resolved.

Just needed to replace the water filter

Removed the one screw holding the unit in place in the freezer and pulled it out. Removed the 3 screws that hold the motor in place on the ice maker. Replaced the motor unit, replaced the 3 screws, and re-installed the ice maker.
Sears wanted $170 for labor for the 10 minute job, plus $130 for the part, which I got here for $65.

Very simple fix, remove 3 screws, two connectors to the old switch

Unpluged fridge, removed 3 screws from each control board (1 on left side and 1 on right side in freezer below ice maker compartment, unplugged and swopped out with new ones. Did one side then the other. Learned about the issue from other people on PartsSelect. Coulden't have been easier. Got parts in 2 days. Works like a charm now.

I Removed 3 screws, pulled off the plate and put the new one on, screwed in 3 screws and away I went. I could not believe how easy it was to order the part and how quickly it arrived. I was very pleased. And I was literally screaming with excitement when I heard the first set of ice cubes drop!

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

I did an internet search about the problem and found the information and experience that other people had. Ordered the part and that's it. One important thing to remember is to unplug the power supply of the appliance prior to making any repair. I short circuited the original board when I tried to plug it back in after cleaning the optics. (The board might have been bad before that.) The red light stop working but the frige is making ice non stop!!

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

i followed the online instructions on how to take the icemaker apart, which were very easy to follow. Once the new part arrived it plugged right in and a few steps later it was back together. within the hour we were hearing the sound of ice dropping into the tray. thanks for all the help this definitely saved us money and hopefully we get many more years out of this icemaker.

I pushed the lever on the filter located at the bottom of the refrigerator and it popped out.

Bought new applicator