KFCS22EVWH3 KitchenAid Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jacqueline from LEXINGTON PK, MD
- Parts Used:
- WPW10662129
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
No cold
Like you video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Whittier, CA
- Parts Used:
- EDR4RXD1
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
Replace ice & water Filter
Open and remove lower cover on filter holder by opening tabs that hold lower cover and remove lower cover.
Firmly hold back of unit and firmly hold and turn filter in counter clockwise to unlock and remove.
Install new filter by holdin back of unit and install new filter by turning in clock wise direction and then replace lower cover.
Firmly hold back of unit and firmly hold and turn filter in counter clockwise to unlock and remove.
Install new filter by holdin back of unit and install new filter by turning in clock wise direction and then replace lower cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas J from WOODRIDGE, IL
- Parts Used:
- W10884390
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Stopped making ice
Tested things a saw that the water valve was working so I figured it had to be the unit in the fridge. There was a possibility that it could be the thermostat or a couple of other possibilities. So I decided to replace the entire unit. That would be easiest and for sure solve the issue. It was simple since the new unit contained everything including the wire harness. So all I had to do was un plug the wiring connection remove 3 screws, remove the unit, put the new one in and plug the wiring connection in. Done in a couple of hours had ice. Within in about 24 hours ice tray was full. And works well
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from AUBURN, CA
- Parts Used:
- W11396033
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Refer lights not working, there are two lights and neither worked. Decided the switch was the problem.
The switch fix but did not fix the problem. I assumed the wires go on the same way as on the old switch. Is it possible if one light Burns out, the other will not work either?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Alexandria, VA
- Parts Used:
- WPW10122078
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Left side end cap deli drawer holder was broken
Ordered left side end cap from Parts Select. They sent me the right side end cap. Had to return the part. They did refund the part price but it cost me shipping both ways. Had to order the part from another vendor. After receiving the correct part it took 19 minutes to remove some shelves, replace the part and replace the shelves, deli drawer and deli cover. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel F from CALEDONIA, MN
- Parts Used:
- W11613295
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Freezer and refridgerator just stopped working.
The Condenser Fan Motor was already removed due to searching for the problem. The new fan motor looked different from the original but I felt very comfortable that Part Select had sent me the new part showing original part number changing numbers over the years. Simply placed the fan blades onto the new motor lined up 2 of the holes placed screws and tightened then plugged the wire ribbon into the Condensor Fan Motor, plugged in the Refridgerator and it worked beautifully.
The instruction video on the Part Select Web Site made it so incredibly easy to install. Installation took under 3 minutes!
The instruction video on the Part Select Web Site made it so incredibly easy to install. Installation took under 3 minutes!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from BUFFALO GROVE, IL
- Parts Used:
- WPW10122078
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
brocken holding pin for Deli Center.
took upparts then put back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from CHESTERFIELD, MO
- Parts Used:
- WP12204827
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Glass shelf Replacement
The new glass shelf was slipped onto the Crisper drawer housing and fit perfectly. I was concerned that the dimensions were not exactly right (too small) but the replacement part fit perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from MT PROSPECT, IL
- Parts Used:
- WPW10534153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Clip cracked on back of kickplate and would not attach.
Pushed on new one as directed online.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carlton from CHICAGO, IL
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light out.
Popped out the old switch and replaced it with the one dying
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from HUNTINGTN BCH, CA
- Parts Used:
- W11396033
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Difficulty removing old switch.
Everything went as planned except the cold temperature (freezer door switch located inside freezer) made deflection of the switch locking tab difficult to remove. Letting the switch warm up was not an option.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Red Banks, MS
- Parts Used:
- 12002497
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken Freezer Drawer Gear
Checked Video online. Had to remove the 2 snap on track/gear covers. Pry out the gear with screwdriver and the gear bearing unit. Align the flat side of the bearing unit and snap in. Position the cut teeth on the gear to match original and snap into the bearing. Insert the connecting rod into the long shaft gear and then push back into the short shaft gear. The video said to remove the drawer front but I did not and don't see that it necessary.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from DEARBORN, MI
- Parts Used:
- WP67003637
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Our old plastic dairy door had a broken part and it kept coming undone
The new door just popped into place. Took seconds to complete. Fast delivery too.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marybeth from VACAVILLE, CA
- Parts Used:
- W11395888
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lost cap for filter
Bought new cap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from NEWTON, NJ
- Parts Used:
- W10619951
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Fridge was leaking water because of bad drain
Switched the drain out using the video tutorial
Fixed the problem
Have had no more drain issues
Fixed the problem
Have had no more drain issues
Was this instruction helpful to you?
Thank you for voting!