KBFS22EWMS4 KitchenAid Refrigerator - Instructions

I unhooked the wire harness from the ref. and took out three screws and pulled the old unit out. I than changed a few parts from the old icemaker to the new and reattached the new ice maker to the ref. and plugged the wire back in. everything is working fine. No problems. Also I was very happy with the ordering process. Thank you!!

Since there were no instructions, I was a tad hesitant but dove in. I was just replacing the right end cap, not the left. Removed the involved shelf as well as the two drawers above. Undid the three screws involved and carefully removed the slide rail end cap as well as a part in the back that was attached. That was the hairy part. It took a bit of time to remove it since everything seems so brittle but I was careful and got the assembly out without breaking anything. Also had to remove the slide rail and humidity control. Nothing to removing and replacing the slide rail. You just have to put it back correctly oriented. This was easy. I just looked at the one on the left, which I hadn't removed. Most time consuming part was cleaning things that were normally inaccessible, before re-installing.

I first replaced the lower (freezer) evaporator thermistor based on recommendation from other feedback, however that did nothing to resolve the problem. I subsequently discovered a diagnostic document hidden under the upper right door hinge, which helped me narrow the problem down to the upper (refrigerator) evaporator fan motor. After replacing the fan motor, my refrigerator is up and running again. The only challenge was accessing and removing the access panel(s) and air column. Once those were removed, replacing the fan motor was simple.

Unscrew filter. Screw on filter bypass

The part came the next day, very quick. The wrong size ended up in box we recieved. The part # we ordered was correct, just a mix up in the packaging process. I called and the customer service dept. had a new correct crisper pan delivered to my door two days later. Even with the mix up it was very fast and a good price compared to other sites. I would order again in the future.

I contacted partselct to see if I could get the end caps with new hinges to correct the problem. My customer service contact was very professional and a huge help in helping me select the correct parts. When the parts arrived I was amazed they were genuine whirlpool parts, fit perfectly, and were easy to install. I have other parts to order and will use partselct again. I appreciate everything they did for me to solve this problem.

Remove rail and removed broken black plastic spring mechanism with new one and then replace rail.

Used socket set to remove screws. Removed the wire harness, then removed lift arm from old ice maker and then put lift arm on the new ice maker. Reinstall wire harness then installed back in freeze with the screws. Video was very helpful. I will do business with Partselect in the future. Shipping was very fast. Thanks Partselect

First, I shut off the water going to the refrigerator, then removed the ice bin. Then I loosened the two screws on the top of the ice maker (the one toward the front was a little tricky, since you can't see it at all), then removed the screw that fastens the lower bracket to the side of the frig. Then I lifted up on it slightly to remove it from the two upper screws, then unplugged the wiring harness from the side of the refrigerator and lifted the whole unit out of the frig.

I then removed the plastic cover on the front of the ice maker, pressed on the tab to remove the wiring harness from the old ice maker, and installed it on the new ice maker. I then removed the metal arm from the old ice maker and installed it on the new unit as well. The last part that I moved from the old ice maker to the new one was the lower bracket, as the bracket on the new ice maker was bent during shipping.

Once those parts were swapped, I put the plastic cover on the new ice maker, plugged the wiring harness back into the side of the frig, routed the fill tube into the back on the ice maker assembly, and set the unit back on the two upper screws. I then put the screw back in the lower bracket, tightened the two upper screws, and then put the ice bin back in and turned the water back on. After a couple of hours, I threw out the first couple of batches of ice and it is now working as it had in the past.

I also noticed, when looking at the old ice maker, that the black plastic coating was coming off the ice cube tray, so it was a good time to be replacing it anyway. Overall, a very easy job (I was prepared for swearing, parts being slightly off, etc.) and it would have been a shame to have paid someone to do it.

Unplug power to refridg/freezer. Removed the screw in rt. rear bottom of ice maker to remove. After removing slightly, unplug pigtail. Remove ice maker completely. Remove large square cover from left side to expose motor. Remove screws to remove motor. Replce with new. Replace ice maker to freezer, plug pigtail back in, put screw back in rt rear bottom, plug refridg/freezer back into power source. Ice was making in about 2 1/2 hours.

Replaced the rail and slide baskets. Also readjusted the basket. This was extremely easy and saved me close to $500

When I received the gasket I laid it out on the floor in a spare room not too far from a heat register to let it straighten out. (If it were summer or sunny weather here I would have laid it out in the sun.) My adult son did the repair - it was very easy to pull out the old gasket and to gently clean the edges with a scraper to prepare for the new install. He followed instructions and other tips but the first section took a while before it would stay inserted. Once it did though, the rest of the gasket snapped in very quickly. I am happy the seal is much improved.

1. Turn your water OFF and pull the refrigerator out from the wall so you can access the back.
2. Use pliers to remove tubing clamp.
3. Remove old water fill tube.
4. I used a putty knife to gently pry out the old fill tube from the back of the refrigerator. Once the fill tube pulls out about 1/4 to 1/2", then you can gently pull the remainder of the tube out by hand. Once I removed my "old" fill tube, that is when I saw the "ice plug" that was causing pressure in the water supply line and caused my water line to pop off.
5. Install new fill tube. The end that goes in first needs to go through a small "ring" inside the freezer (this "ring" is not encountered until the fill tube only has about one more inch to be inserted into the back of the refigerator. I could barely see this "ring" if I opened the freezer drawer and stuck my head in as far as I could. I had to gently rotate the new fill tube until it cleared the "ring". You will feel some resistance until it lines up properly.
6. Snugly push in the part that stays on the outside of the refrigerator until it looks like it is sealed.
7. Gently push up the water fill tube where it belongs in the new part and replace the tubing clamp.
8. Turn your water on and make sure there are no leaks (I left my refrigerator out for about an hour).
9. Push your refrigerator back in place.

Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked

repair was extremely easy.
Whether it was magnets weakened or seal getting stiff with age not allowing it to seal well, these gaskets improved it. Still not as strong a magnetic pull as it could be though. I will also say that the seals didn't pull tight at first. It seems the seals needed to flatten a bit before the magnets did their job.