KRCA06XRSS00 KitchenAid Refrigerator - Instructions

Watched your video pull the door off switched parts and all done . Thanks to your web site it helped me diagnose and fix the problem

1. Turn thermostat down to ensure cooling cycle turns on. Open freezer compartment and listen for air flow/fan. If no air flow or fan, but compressor seems to be working, then proceed to next steps. 2. Turn thermostat up to shut off refrigerator cooling cycle. 3. Open freezer and remove wire shelf (if installed). 4. Using nutdriver or socket set, remove screws securing metal panel on the back wall of the freezer interior. 5. Pull metal panel out to expose evaporator fan and evaporator coil. 6. Ensuring area around fan is clear, turn thermostat down to again start cooling cycle and check if fan operates - if not, then fan needs to be replaced. 7. Turn off refrigerator and unplug from electrical outlet. 8. Order replacement fan (unless you happen to keep one in stock). 9. Remove two screws securing fan and fan bracket assembly to back wall of freezer, note wire connections to fan (red, white and green), disconnect wires and remove fan assembly. 10. Gently pull off fan blade, it is a compression fitting. 11. Remove two screws holding back and front fan brackets together and remove fan motor. 12. Remove rubber gasket from front and back of old motor and insert then on the new replacement fan motor (these rubber gaskets align to openings in the fan brackets, thereby holding the motor in place when installed back into the brackets). 13. Reinstall fan brackets onto new motor matching how the old motor was assembled. 14. Press the fan blade onto the new motor shaft. 15. Reinstall fan motor assembly onto back wall of freezer. 16. Reconnect wires to new motor as they were previously connected to old motor. 17. Reinstall back wall metal panel that covers the fan motor assembly and evaporator coil. 18. Reinstall wire shelf (if applicable). 19. Plug refrigerator in and adjust thermostat to normal setting to initiate cooling cycle. 20. Open freezer and listen for fan and airflow, if you hear it operating correctly, then close freezer and refrigerator and confirm temperatures after refrigerator has cycled through one full cooling cycle - adjust thermostat as necessary. 21. Tell your spouse or significant other that for less than fifty dollars you just saved the price of replacing the refrigerator.

The repair was very easy, unplug ref. open freezer door, and remove base plate, then remove screws on back plate. I had to tilt top of back plate to remove from freezer. This gives you access to the evap. fan Pull of the three wires, and remove screws from fan bracket, which bolts to the back of ref. Remove fan motor from bracket (2) screws, remove motor, and put replacement motor on bracket, pull fan blade off old unit and push on new motor shaft. Reverse the installation, and you are done. Pretty easy.

First I removed the top bracket cover screw with a 5/16" nut driver. placing it aside, I removed the three screws holding the top door hinge off using a 5/16" socket on a 1/4 drive to free the screws , then continued to remove them with the nut driver. placing them aside on top of the refrigerator. Then I lifted the door up and off the lower hinge and laid the door down on my kitchen counter. I removed the lower hinge piece from the lower bracket still on the fridge with a 5/16" nut driver and installed the new piece in its place and also applied a few dots of Vaseline on the lower hinge piece, I then removed the screw and lower bracket from the door and installed the new one and also applied some Vaseline on this piece also. I also took a rag that had been dipped in olive oil and rubbed the entire gasket surround the door to lubricate the gasket to keep it soft, then I reinstalled the door back onto its lower bracket, and then lined door back up correctly and reinstalled the top mounting bracket and screws then the cover, and then tested door. Door opens now with no noise and opens easier also.

I did it a bit different from instructions mainly because I disassembled it to troubleshoot before going on line to find part and "easier" instructions.I had a 5" block of wood and cut a shim to use with that to hold the door up. I got on my hands and knees with a mirror and removed the lower hinge plate then the screws holding the upper and lower cams. These both were quite worn so I just took them to my shop and with a hand grinder I rounded off the sharpo corners of the cogs of both cams and then reassemble the hinge plate and cams. This eliminated the loud clicking and the door closed easily but I was afraid it woulod not "Auto Close" when needed so I went online to find this page with the parts needed along with wonderful instructions. I ordered both upper and lower cams which came 2 days later (THANKS). I installed them my way since I did not want to empty the door contents and remove the whole door. I used the block, mirror and nut driver to R&R the bottom hinge plate and both cams. Time was still less than 15 minutes, Easy Fix, Thanks guys! Cheers, Ben

This is a very easy fix. Begin by emptying the contents of the door. Then, just remove hinge cap and remove the three hinge screws. The door can then be lifted off the hinge pin and placed on its side. Once this is done, replace the two can pieces (one on the door and one on the frame). Then just lift the door back in place and secure the hinge. This job can be done by one person (maybe two if you need help place the door on a work surface) and will take just 15 minutes.

If you are having this problem, read this. My refrigerator door would not stay closed. This was over a year and a half time period. I thought it was something complicated and told my wife to call a repairman. Thank goodness she does what she does best - not listening to me! I finally had enough and went online and googled my problem and found PartsSelect. PartSelect had a repair video showing how to fix the problem. If you are like me, I'm very cautious about purchasing from a website in which I'm not familiar. PartsSelect is a reputable site (I promise I do not work for them). My refrigerator is over 8 years old and they had the part I needed, a lower door cam, along with a video on how to install the part. This honestly took about 5-10 minutes to do and I did it without any help. I was so aggravated at myself for waiting so long at doing this!! I actually ordered 2 of these parts, just for the next time. You can do this.

Removed the door, removed the old lower door cam, and replaced with new cam.

Followed the Partselect instructions - removed door, removed old cam and replaced with new cam. One lesson learned. There are two cams - one that sits on hinge below door and one that is up inside bottom of door. If you are replacing one, replace them both.

I removed the door and switched out the cams on the bottom. Super easy. Door closes perfectly now.

I would never attempt an appliance repair but after watching the video instructions for installing this part I decided to give it a try even though I'm dangerous with a screwdriver. After retrieving a nutdriver from my $39 handy dandy tool set, it was a piece of cake. Upper hinge cover, hinge, door removal, comes off in a matter of minutes. Only problem surfaced when I went to install my new cam in the lower hinge. It didn't fit. It was actually for the upper door hinge. I reinstalled the lower plastic piece (whatever it's called), tightened it down, put the door back on (you can do it yourself if it's the refrig. side) and popping sound was gone. I guess the bottom hinge plastic piece was probably loose but you can't tighten it unless you remove the door. I now have a upper door cam in my drawer ready when it fails and will replace it without hesitation.

Removed door, removed both upper and lower cam and replaced, applied small amount of vasoline and replaced the door. The entire repair took less than 5 minutes. Door works great. When replacing the cam you need to replace both the upper and lower cam. When you order the parts, the upper cam is on the door schematic and the lower cam is on the refrigerator body schematic. I originally only ordered the upper cam.

All you need is nut driver. Top hinge has 3 screws. Once you remove the screws, lift door. It is light. I place door of my sofa. I removed screws and pried the cam insert with a spatula. You can also you flat screwdriver. I also replace the other piece located at bottom of refrigerator. Now place door back onto metal rest. May need someone near floor to guide you. Once on the rest, close door and replace top screws. Forgot to mention that I emptied door shelves before removing door.

Pulled out the Fridge. Removed the plug. Removed the back panel screws with nut driver. Vacuumed the coils & fan area. Disconnected the fan cable. Used a socket and thumb ratchet to remove the 3 mounting screws from its sheet metal bracket. Slid the old fan assembly out. Assembled the new Fan blade onto the new motor shaft and attached the adapter cable to the fan connector. Slid the assembly into place and reattached with 3 screws using socket and thumb ratchet. Connected adapter cable to fridge harness and plugged in the power cord to test the fan. With it working Quietly and knowing the the problem was solved, the back panel was reattached.

Instructions were really clear and easy to follow. Hardest part of the job was moving the refrigerator away from wall after it was filled with holiday groceries.