KBLS20ETSS00 KitchenAid Refrigerator - Instructions

Took a putty knife and
Removed the old switch removed the spade terminals from the old switch and replaced them on the new switch and just pushed the new switch back in place

Pop loose the plastic grate at the bottom.

Locate and remove the wheel leveling screw from the front bottom corner.

Remove cotter pin from the pin that mounts the wheel assembly to the refrigerator. Tap out the mounting pin.

Lift out the wheel assembly.

Remove the Roller pin from the wheel assembly. I used a Dremel tool with a cutting disk. A hack saw will also probably work.

Install the new roller pin and wheel into the wheel assembly. Use a hammer or vice to peen over the end of the roller pin.

Reinstall and adjust wheel assembly.

(1) Removed the three screws which attached the ice maker to the freezing compartmnet wall in refrigerator; (2) Disconnected the power to the old ice maker; (3) Removed the old ice maker from the freezing compartment of the refrigerator; (4) Took the white front cover off of the old ice maker; (5) Disconnected the wiring harness from the old ice maker; (6) Removed the "ice making-stop arm" from the old ice maker; (7) Placed the items taken from old ice maker on to the new ice maker; (8) Reconnected the new ice maker to the power; (9) Placed the new ice maker in the proper position in freezing compartment of refrigerator and replaced the three screws. JOB DONE!

First turned off the water at the valve. Next I undid the 5 screws holding the plate that holds the pump. Next disconnected the power connectors, then the water lines. Next undid the screw holding the pump, removed pump. Next, mounted the new pump to the plate, this was tricky because it has to fit kind of upside down, so you have to wrangle it into the proper position then align the screw hole. Next, secured it to the plate with the screw, re-connected the water lines, then the power. Before mounting it back to the fridge, I tested to see if it worked, well, it didn't. My heart sank. I re-checked all connections, I redid the entire process, disconnected and re-connected and still did not work. I researched the problem online and someone posted maybe the water filter might be clogged or defective. So I removed the water filter and put the stop plug in, and it worked perfectly. I went and exchanged the filter and plugged it in and still had the same problem. I am now suspecting the filter receptacle is the fault, but we will do without that for the time being. But the pressure is much better so changing the pump was still necessary. All in all a very interesting repair. I learned a lot about how the system works and now I need to replace the damper, it is very noisy.

Lower the filter bottom housing to gain access to the filter. Unscrew the filter and install the bypass cap. Secure the lower filter housing to the top assembly.

It actually took 1 day and 15 minutes to fix this problem.

I removed the drawers and shelves in the area around the pantry. I carefully took apart the sliders and plastic parts that comprise the endcap/temperature adjuster. Then I tried to replace the unbroken part into the assembly. At that point I realized that something was wrong and I had ordered the wrong part. So I cleaned and put the broken part back in the refrigerator to wait for the replacement.

PartSelect customer service person was terrific and had the correct part on the way to my home immediately. I don't know how, but it arrived the NEXT day!

THEN, it took me 15 minutes to unscrew the sliders, endcap and replace both.
Thank you PartSelect.

Received the union I ordered, then discovered that the tubes were different sizes, so I had the wrong part. I had read elsewhere that it was necessary to trim the two ends of the tubes with a box cutter to stop the leaks - I did this, and the leaking stopped. I was then able to go to a local hardware store and get a 5/16 to 1/4 union and replace it. The leaking is stopped, and the water supply in the door is now working like new. No problem with partselect, but I did buy a caliper so that I can check tube diameters if I ever have a similar problem! This is a great site to find instructions - well worth the time to search!

Removed the top door hinge cover.
Remover the four 12mm hex screws.
Lifted empty door off bottem hinge support.
Removed old door closure.
Put some silicon lub on the new closure and installed.
Reversed the removal steps.

But this did not fix the problem. Will have to remove the door and inspect the inside of the door's lower hinge assembly.

Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one.
But Parts Select is a great place to order from. Thank you.

You need to lift up the glass part and simply fit it the center rail in, very simple

followed the instructions provided and that's it!

Very simple. Matched female plugs with respective male color coded prong; pushed together then inserted unit in slot of freezer sidewall and rotated into position...job done.

Unscrewed back of fridge and unplugged relay from compressor and plugged in the new one remember that the new one turns 180 degrees from existing switch.

Took the valve off from the back of the frig and reinstalled the part I purchased from Part Select. The part was an exact OEM part, not a substitute that others had. The install went very smooth and once again we have water and ice from our frig. Can't thank Part Select enough for the thier sales team and the order department. They made sure that I got the exact part that I needed. Customer for life.... Mike D. Wisconsin

Plied off the relay switch with a screw driver. I could not pull it off by hand. Disconnected the wires to it and replaced with new part. Had problem getting the part back on and lining up the pins with the connector. I had to line up one pin and start at an angle and roll the part onto the contact pins.
I was impressed with the one day delivery without paying because it was shipped from a warehouse in California where the repair was made.