KBRS22KGBT13 KitchenAid Refrigerator - Instructions

First I removed the cover to the evaporator in the freezer section and found the coil iced up, then I turned the defrost timer until it clicked into the defrost mode, the heaters came on so I left the timer in the defrost mode to defrost the coil, it stayed on and did not change. The timer motor was bad, I ordered a new part and had to manually defrost the refrigerator by turning the timer. To replace the part I had to first unplug the power cord then pull the kick plate off at the front of the refrigerator and remove two screws that hold the timer in place, then pull it out unplug the electric plug in the new timer secure it with the two screws and put the kick plate back in place. I then plugged in the power cord and the refrigerator came on as is now working great..

There were no instructions with the new gasket which made the job difficult. After great difficulty I called an appliance store and learned that the gasket should be soaked for several minutes in very hot water to make it pliable and easier to install. Also, the plastic insert that the gasket fits into should only be loosened and not removed when inserting the gasket. Lastly, the door should be removed and placed on a table to allow leverage to be applied. Installing it while still on the door is almost impossible.

replaced water valve and new icemaker.

Water Intake valve for icemaker in Amana refrigerator
We found that the icemaker was not getting water due to a faulty intake valve. The original valve had a plastic coupling on the vinyl tube leaving the valve. The replacement valve had a quick connect coupling. Replacing the valve with the new part gave a significant leak. After discussion and viewing YouTube directions multiple times, the part was returned; and a new part was sent. It also leaked.
After searching, a video was found that dealt with the no-fail quick connect. The problem was not in the quick connect but in the tube from our refrigerator which had a spring inside the last five inches of the tube. This aided the prevention of a leak when the original plastic coupling had been installed.
SOLUTION: Removing the part of the tube with the spring using a clean cut allowed the quick connect to work preventing the leak. This needs to be mentioned in the how-to videos to save others having a problem. Also, these instructions with the part would be helpful.

The longer than usual repair times shown above were the result of the spring insert in the plastic water tube of the refrigerator. Nowhere in the how-to instructions were references made of either an insert in the tube or quick connect procedures.

We were well pleased with the support rendered by the PartSelect staff.

snapped the new ones on the aluminum bar and inserted into the freezer

I removed the back cover in the freezer section by removing six screws. The entire coil, the thermostat and the lines were all iced over. I used a hairdryer to defrost everything. I removed the thermostat by uncoupling the connectors and unclipping it from the coil tubing. I found the thermostat was bulging and deformed. I jumped out the thermostat using an insulated clip lead. I taped it so it would not short to anything. I plugged the unit in, turned the unit to "1" and advanced the defrost timer to defrost. I could hear the water hissing on the coil. I ordered the thermostat. It arrived in 3 days. The new one had a different terminal. I cut off the matching one from the old part and used a scotch-lok to make the connection to the new part. I slapped it in, dressed the wires and replaced the cover. I noticed that when I advanced the timer after replacing the thermostat, it did not immediately come on. The thermostat has an operating temperature window. I checked it several days later and found no frost. Everything works great.

Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.

First let me say the part arrived much faster than I anticipated! I was able to use the box (cardboard) the part came in to cover the freezer while the door was being worked on. I did not remove the door, but did remove all the screws that held the door inner part that the gasket fits around. Like another person wrote, my insulation in the door was frozen. I took that out and put new insulation in. I then fit the gasket around it and then screwed it back on. I have an electric screw driver and without the bit, it fit these hex screws perfectly, so I was able to unscrew and screw quickly.

Unfortunately, I realized the cause for the dripping was due to a faulty defrost thermostat. I'm guessing that part will arrive tomorrow. We did need a new gasket, however, so I don't regret it.

First of all let me say I can't believe I fixed it! And I can thank this website for it, they also had my part at my front door in less than 24 hours. I am so amazed! I am a stay at home Mom, and because my husband is always off with the military I knew the job was up to me to fix. And because times are tough we certainly couldn't afford a repairman. After reading many stories here about the same problem I had, I diagnosed what was wrong with my refrigerator. The defrost thermostat was faulty. First thing to do was turn off the refrig and then unplug it. I then emptied the bottom freezer, used a screwdriver to remove back panel wall. Lo and behold the coils were covered with ice. I defrosted the freezer using a blow dryer, also had to empty the drip pan in the back. when it got full of water. ANd because there is no way to remove the drip pan, I actually got a small air hose from my son's old fish tank(clean one) and then siphoned the water into a pot, took all of 10 minutes! I then used needle nose pliers to remove the bad defrost thermostat from the refrig's wiring.The defrost thermostat which had a bulge in it so knew I was on the right path. I looked at the new defrost thermostat and they had different ends on it then the one I just removed, and I remember reading what another member did, and that was to cut off the connecting caps, strip the wires , use electrical tape to join them and use a crimping tool to place the old caps on to the new defrost thermostat .I then inserted the thermostat to the freezer's wiring. Hope that makes sense to everyone. WEll, everything is running great! Thank-You Part Select, you saved me lots of money!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires... Put a thermometer in a glass of water & now runs at 38 degrees.

Talked to a bud who does this kind of work and he walked me thru the simple job. Also watched a you tube segment. Very easy job. Took off the front kick vent panel. Unscrewed the metal holder and unplugged old part, plugged new part in and put panel back on. Turned on unit and it is working like a charm. Got my fingers crossed just in case.

I slid the bar into the end caps, then slid the end caps into the slots on the door. No tools were required. My fridge is old, and I was very pleased that I was able to find the part.

I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.

Once I removed the contents of the freezer I found ice on the inside back panel Removing the panel I found ice on the cooling coils and the defrost thermostat was bulged out where the wires were attached.I removed the panel with the nutdriver as shown in the video. I removed the ice maker connection and removed the panel from the freezer section. I then had to manually defrost the area with a heat gun. The ice had actually covered the Defrost Thermostat - which was bulging where the wires were attached.. The defrosting took the majority of the repair time - the actual Defrost Thermostat replacement only took about 20 minutes once I could get to it. I spliced the wire with a crimping tool as discussed in the video. Once all was defrosted I reversed the operation.Overall, a very simple part change out. The video was extremely helpful - if nothing else to mentally prepare me for the task.

Took the ice maker out with three screws hving turned water off and unplugging fridge. Put a new one back in with the three screws. plugged fridge back in and turned water on. All done and everthing worked fine.

Ronald Stonis