KTRP20KDAL01 KitchenAid Refrigerator - Instructions

I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.

taped the door shut ,measured a block of wood and stuck it under the door for support.....unbolted bottom hinge,slipped on hinge bracket and reassembled.no muss no fuss.

it was a simple repair once I located the part I had to replace . I really like your speedy delivery of the part I needed Thank you Pat Crotty

Forty years ago I serviced air conditioners and all kinds of refrigeration. At that time starting relays were electro mechanical, I hadn’t looked under a refrigerator in a lot of years and was surprised to find out that the new relays were solid state. The defective one had a bunch of broken pieces floating around in the case. I jury rigged a starting cord and confirmed that the compressor would start and looked at running current for thirty or so seconds. I ordered a new relay kit and it worked just right. I’m seventy five years old and it takes me longer to get up off the floor than it took to replace the parts. Your delivery was first rate the parts got here before I finished doing the paint touch-up on the door under the ice maker/water dispenser. Fed ex was easily three to five days faster than the brown truck.

unplugged relay and plugged in

Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

With the help of the website I was able to verify that the part I removed (in the area of the clicking sound) was probably the part required for replacement. I ordered it, installed it... IT WORKS (I knew it the moment I plugged in the power cord and heard the compressor kick on). Saved me from buying a new fridge or calling a repairman. I'm a 58 year old woman with no appliance experience. I watched the videos and installed the part without any trouble. Thank you PartSelect for your easy to use website instructions and helpful hints.

1. Unplug the refrigerator. 2. Remove the back cover at the bottom of the refrigerator. 3. Remove the two screws holding the vertical black bracket the fan is mounted to. This allows the bracket to move easily. The bracket does not have to be removed. 4. Removed the four screws holding the fan bracket to the vertical bracket. 5. Unplug the power connector from the fan motor. 6. Remove the entire fan bracket assembly from the refrigerator. 7. Remove the 4 screws holding the fan motor to the fan motor bracket and unmount the fan motor. 8. Remove the nut holding the fan blade to the fan motor and remove the fan blade. 9. Reverse the process, mounting the fan blade to the new motor, screw the motor to the bracket, screw the bracket to the vertical bracket, screw the vertical bracket to the refrigerator and plug the power connector back into the motor. I did not have to use any of the extra mounting hardware or electrical hardware provided with the kit. It might be a good idea to purchase a new fan blade with the motor kit, the fan blade can get pretty grungy. I cleaned the fan blade with some degreaser before remounting it.

I did the repair just as your video showed me. It worked out great.

The suggested repair parts were correct and easy to install. May I suggest wire nuts or crimp type nuts be included in the repair kit. I would recommend this web cite to anyone do it your self repairs. Thanks, Mike NH

This problem can be caused by 3 different part failures. Timer, thermostat or heater. After contacting a service repair shop I was told that most often it is the thermostat. The cost of the repair would be at least $115. To much for an old refer. So I ordered the part from Partselect for $33. and put it in myself. Step1 cut the power to the refer. Step2 remove ice maker if you have one. Step3 remove base and back panels in the freezer. Step4 the coils were badly frozen so I used a hair dryer to thaw it out. Would have waited a long time for it to thaw out otherwise. Step5 The thermostat is clipped on to copper tubing next to the coils. Unclip it and cut the wires close to the thermostat. Strip the wires and wire nut the new thermostat. Clip it back on to the copper tubing. Put it all back together and start it up. It's over a week know and no problems. Note: We have whirlpool appliances that are over 16 years old. I have repaired the washer, oven, and now the refer with parts from Partselect. Good company. Always received the correct part within about 3 days from ordering. If you are able to do the work yourself you can save big bucks and keep your appliances running longer. Good Luck

I just simply eliminated the ice buildup with hot water and a knife. But I still have the Defrost Timer Kit for future use.

Took a little while to figure out that I needed a flat tip screwdriver to lift up on the top of the plastic housing in order to tip it forward and remove it. After that I used pliers to remove the wires from the old parts and place them on the new. Removing and replacing the parts was performed by hand.

Fan was barely rotating. So unplugged, removed back cover, removed fan and motor from frame work. Removed fan blade from motor shaft. Spun motor shaft which seemed fine. Pryed off back cover of motor to find a large but dry felt washer and a helical capillery slot formed into the motor shaft for carring oil from felt washer to the bearings. Added 30 wt motor oil and some 3in1 oil to felt and reassembled motor, fan and frame work. Plugged in power chord after getting rid of dust and dog hear on coils and is working like new.