KSSC36QTS02 KitchenAid Refrigerator - Instructions

After taking apart the ice maker, the only obvious replacement was the motor assembly. I check various Internet sites and found the best price at PartSelect.

I removed the ice maker from the freezer after turning off the ice make switch. Removal was easy with only one screw holding in the entire assembly. The ice maker has rails that allow it to slide in and out like a drawer.

After R/R the motor assembly and returning the ice make to the freezer all that remiand was to see if it worked.

Within 10 minutes I had the wonderful sound of water filling the ice maker tray. Within 30 minutes of that, ICE!!!

Shopping, ordering and shipping of the part was fast and efficient. I'll go with PartSelect for all my future appliance needs.

Simply cut the water tube on both sides of connector and push in the new one.

Unpluged the refrigerator, removed the burnt out switch by unpluging it, plugged the new one in re installed the switch into cover. Plugged in refrigerator replaced cover. Done. Easy as one two three

With instructions from PartSelect.com this was an easy fix. I tested the motor's electric as suggested and was satisfied that the Motor Module (WPL W10190935) would correct the problem. UNPLUG THE REFRIGERATOR! I popped the outside plastic cover off to expose the unit. (1) remove the wire unit that runs the length of the cube maker (2) remove the 3 screws that secure the motor unit and carefully remove it (3) carefully line up the new unit, slide in place and replace the 3 screws (4) install the wire that was removed in step(1). Connect electric to the refrigerator and wait about 2 hours for your first ice cubes. PartSelect.com is the ONLY supplier that you will ever need! Great instructions and trouble shooting suggestions. Shipping is incredibly fasssst! Customer contact is awesome. Don't hesitate to buy from them! Saved me about $200.! Good luck....Tom in SC

followed the video instructions on the PartSelect website. No problem. Ice in about 2 hours! tnx

These are instructions are for replacing the see-through covers (manufacturer part number WPW10131132) on the two upper door utility bins.

First it is easiest to remove the entire bins rather than hold open the fridge doors while you work.

There are two plastic studs on the bin body designed to fit through the holes in the bin cover. The tips of these studs will have to be simultaneously compressed with pliers (thus two sets of needle nose pliers) in order to slide the old cover past the studs to remove. Unless you have three hands, you will need another person to slide the cover left past the studs while you are handling both sets of pliers. Although the studs are pretty flexible, be careful not to break them off in the process. Once the cover is past the studs you can pull in free.

installing the new cover is easy. Since the studs are tapered, simply align with the holes on both ends of the the cover with the studs and apply pressure to the right. The cover will slide over the tapered studs and lock into place.

Once the new covers are installed, simply reinstall the complete bin back on the refrigerator door. Just push and snap in the tracks on the refrigerator door interior body.

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

Very easy to order from parts select. Took seconds to replace.

removed ice bin then removed 2 screws and removed broken button. replaced with new button and 2 screws. 5 minutes max thanks for quick response with part

ordered the part, pulled out the icemaker unit, removed the module, put the new module in, reinstalled the ice maker unit and let it run.

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

Starting at the bottom, with a flat blade screwdriver pry the front cover off the opening. Unplug the wire connector from the back, remove the cover plate holding the switches and light socket by pushing out on the plastic clips on each side. Use something like a bungie cord to hold it up out of the way. Carefully unsnap the clear plastic ice shoot from the push arm, next carefully unsnap the cover door from the push arm. Clean anything that needs cleaning (CLR works great on hard water deposits)
Install everything in reverse order, the cover door first, ice shoot next, switch plate, plug in the wire connector and snap the outside cover in place.

Followed on line video

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

Easy repair, unplug the fridge and then remove the 3 screws on each side of the freezer holding the emitter and receiver. Swap the boards and re-install. Takes less than 10 minutes.