KBRS22KGBL4 KitchenAid Refrigerator - Instructions

I removed the ice maker with 3 screws after having shut off the water. I tried getting the part locally but thought it was a bit much. Of course after having had ordered the wrong part, PS51041 and having it over nighted here and paying the return shipping I would have saved money getting it locally. When I finally got the right part I used the power cable and level lever off the old maker and reinstalled the ice maker in just a few minutes with a nut driver and screwdriver. Thurning on the water in about and hour it started making ice. When ordering online make sure you can get a large enough diagram to see what you are getting. If you can't ,call their phone number ant talk to a live person.

I left the new seal out in the sun to warm up, while it was warming up I took the door off of the fridge and laid it flat. I removed all of screws holding the plastic shelves in place, removed the old gasget fitted the new one and reinstalled the door.

Followed the video instruction and it was fairly easy to install. Let the gaskets sit for a day to reshape itself. Started by loosening the screws then removal of the gasket was done. The only hard part was to align the Gasket evenly. Not removing the doors made the install a little more difficult for alignment.

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

Remove 3 screws, took top hinge out, fz door and inserted shim...done.

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

I followed the directions that came with the new part. Thank you for making it so easy. You sent me everything I needed to make the repair.

Very simple fix, remove 3 screws, two connectors to the old switch

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks

Slid the end caps onto the shelf, placed the tape on the pieces as noted in the directions, and put the shelf back in place. Fast service, exact part, easy to find on the web site! Great!

First I removed the cover to the evaporator in the freezer section and found the coil iced up, then I turned the defrost timer until it clicked into the defrost mode, the heaters came on so I left the timer in the defrost mode to defrost the coil, it stayed on and did not change. The timer motor was bad, I ordered a new part and had to manually defrost the refrigerator by turning the timer. To replace the part I had to first unplug the power cord then pull the kick plate off at the front of the refrigerator and remove two screws that hold the timer in place, then pull it out unplug the electric plug in the new timer secure it with the two screws and put the kick plate back in place. I then plugged in the power cord and the refrigerator came on as is now working great..

I simply used my cordless drill with the right sized socket attachment to remove the screws. I left the door on which wasn't as difficult as I thought after reading other stories. I even had to contend with my three year old who wanted to know what was going on and if she could help. As my wife is deployed it falls to me to become both parents, watch after her and take care of chores. With all that said it still only took me about half an hour to replace the old gasket with the new one. As far as the gasket goes I wish the magnet was more powerful because there is still a gap unless you push and hold it closed for an extra second when closing the freezer. A pain but at least it is not torn. Before buying I recommend searching for a parts/service center that that talks about the whole part not just how to replace.

replaced water valve and new icemaker.

I loosened(but did not remove) the 1/4" sheetmetal screws around the perimeter of the door liner. (they are numerous and they are hidden in the fold of the gasket) I removed the old gasket. With the screws still loose, I installed the new gasket. After insallation I re-tightened the liner screws. Several gaps were noted and eliminated by gently heating the gasket with a hair dryer. (be patient , it takes some time)

First we read all the comments by other handymen. This was really helpful. Then we took the door off and removed the old gasket with a nut driver. We tried to slip the new gasket under the edge with a thin spatula and didn't have much luck. Then we remembered someone saying that is was a good time to take the door apart and check to see if there was ice build up in the door. It was so bad we took out the frozen insulation and replaced it with new....$4.00 at the hardware store. While the door was apart we put the gasket on and put it in place and tightened it to the door. This worked very well for us. This saved us from having to buy a new refrigerator/ freezer. Thanks.