KBSD702MSS00 KitchenAid Refrigerator - Instructions

I replaced the Electronic control boards because the indicator lights were letting me know that there was a problem, but!!!! when that did not fix the problem, I took the ice maker out and removed the control module from the end of the icemaker only to find out that water had gotten in there and corroded the electronic contacts... this may have been why the indicator lights were not working on the emitter and receiver. I was going to purchase just the module, but the entire ice tray was beginning to de-laminate and plastic was flaking off all over. To make a long story somewhat shorter, I purchased a new icemaker and it works fine... one caution though... My icemaker did not come with any information that told me I had to flip the icemaker to the "on" position from vacation mode by inserting a screwdriver in the back of the module inside of a small white ring. This hole is where the shut off arm WOULD go if my model had one.

My ice maker about six months ago started to ice make very intermittently and eventually stopped all together. The emiitter no matter what I did was giving me two flashes then a pause, over and over again. I purchased the emitter kit and with a Phillips screwdriver in about five minutes my ice maker kicked the sulinoid on and ice was already started!!! Fast and easy repair!!!

I went online and watched a U-tube video that said it was most likely the electronic emitter and receiver boards and showed how to replace them. I first unplugged the appliance (just to be safe) then, I unscrewed the screws holding the faceplate on. The board simply has a plug which you unplug with a little care and effort. I then plugged in the new board, resituated it into the hole and screwed the faceplate back on. You simply do the same for the other board on the other side. Viola! Lots and lots of ice!! The guy at sears said I shouldn't do work on such a complex appliance. Probably because I am a woman! Anyone can do this job! Winning!

After unplugging refrigerator, removed emitter and receiver cover plates on each side of freezer unit (3 screws each) and mounting screws for circuit boards. Unplugged old boards and plugged in new ones and reinstalled boards and then cover plates. Although, indicator code lights seem to still indicate a problem, ice maker has resumed operating after 24 hr.

My icemaker quit 3 years back and at that time I searched for do-it yourself repair books with no success. I found this parts place web site and people having the same problems as myself. I purchased the parts as others have and problem solved! Ice all the time, woo hoo!

installed new parts

Did not have elec. schematics or instructions, thought the problem may be the emitter/receiver. Ordered these parts, and included in the package were instructions for testing the e/m bd. Followed instructions for testing the e/m and determined the e/m was OK. Did not remove the boards from the box. Checked the internet and found schematic for the ice maker, tested and determined the ice maker was faulty. Problem solved.

1) unplug the refrigerator
2) remove the cover plate for the sensor board on your left facing the refrigerator
3) unplug the sensor board then remove the board from the cover plate.
4) install the new board onto the cover plate and
reinstall the board in to left side of the freezer compartment.
5) repeat this proces for the right side of the freezer compartment.
The two boards are very different and you will have no problem telling the difference between them.
6)Plug the refigerator back in and observe the red indicator light on the right hand side of the freezer compartment (it should be blinking) . Then hold down the flap on the left hand side and the blinking red light should go solid on. If it hasn't you have another problem with the ice maker.

The best part of the repair was how easy it was to find and order the part. Instead of searching the parts houses around town I just went to the PartSelect web site, quickly found and ordered the part in about five minutes, received the part the next day at my home and was ready to make the repair. Wow! What a pleasure for something to work the way it was meant to. Removed old switch located by prying out with sharp knife or screwdriver. Don't worry about breaking it or cracking plastic. Disconnect(unplug) wires from back of switch. Replace (plug-in) wires on back of new switch. Insert in location of old switch. Finisheed.

i replaced the electronic control board of emitter and receiver

A snap! The part arrived the day after I ordered it. (How, I don't know). The video showed exactly what to do. I did it. Ice maker now works like a charm. Thanks.

My Ice maker would not release ice cubes, it thought the ice bin was full. So I got on You Tube and looked up how to videos. Partselect videos were the best that I found and the prices were low also. The whole repair took about 15 minutes.

I first ordered the electronic control boards. However, they arrived with an Instruction Sheet. The diagnostic procedures listed on that sheet identified that the optics were working properly, so did not use the electronics. That left the motor assembly as the culprit. Ordered that. The motor assembly arrived promptly and installed easily - just like the video. Ice maker began making ice immediately. Thank you PartSelect.

replaced electric control board, defrost for six hours. next day (24 hours) same problem, dusterhoff2928@charter.net

Being 50 miles from the Sears with a 7 year old unit, I actually changed out both board (a kit) which was 9 screws. 3 screws in the outside panels, and 2 in the larger board, and 1 on the smaller board. Both both boards plug in. I also changed the actual ice maker which unplugs and slides out on my unit. Remove a single screw (1/4") on bottom to remove a plastic shield that covers/protects the plug in. A plastic arm lock is in the bottom guide tray, push it up first. Then unplug the unit. Three more 1/4" screws in bottom to remove the custom plastic mount. Then reverses the process to install the new ice maker. Total $175 plus 1 hour labor. In 6 months the unit will have paid for the repairs. I hope to get 5 years of service from the job