KRFC300ESS09 KitchenAid Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Alexander from Chicago, IL
- Parts Used:
- WP12656105
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Lid to pantry broke off.
It was very easy. I removed the two crisper drawers and the glass shelf above the pantry section. I removed two bolts with a nut driver and one screw from the slide track. I pulled out the broken piece and did that all in reverse. Took 5 mins tops.
Also I wanted to say I got my replacement part in two days with standard shipping.
Also I wanted to say I got my replacement part in two days with standard shipping.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LARRY from HUTTO, TX
- Parts Used:
- W10827015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Our deli drawer had a cracked cover window.
Extremely simple to replace the entire cover. Just had to press on the sides to remove the cover from the hinge pins, then reinstall.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from ROCHESTER, NY
- Parts Used:
- W10827015
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broken pantry drawer lid
took out old lid, took out drawers above this drawer to make it easier to work on. installed new drawer simple by hand with no tools. put other drawers back. very simple no tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DEBRA from STATE COLLEGE, PA
- Parts Used:
- WPW10171529
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Did not have a ice pan
Ordered and placed in the freezer under ice machine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from BEVERLY, MA
- Parts Used:
- W10830162, WP67002659
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Took me less than 5 minutes to install both
Pulled out old gasket and new one pushed right in with ease.
Removed drawer trim and snapped in on new one in 30 sec. took longer to empty the drawer than it did to replace
Removed drawer trim and snapped in on new one in 30 sec. took longer to empty the drawer than it did to replace
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Plattsburgh, NY
- Parts Used:
- W10827015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Cracked lid, broken hinge - right side
Two phillips head screws out to remove drawer slide. Three screws to remove right side drawer support. New support placed, new lid snapped into place. The right side has an adjustment lever. Re-routing that took the longest. The arm had to be removed and twisted to get the adjustment knob off and on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlie from HARRODSBURG, KY
- Parts Used:
- WP12656105
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Broken pin to door
Easy
Was this instruction helpful to you?
Thank you for voting!
Empty box sent with no part!!!! No customer service help because of covid
No product was sent in the box for the shaft I received an empty box from them cannot perform any repairs because I got no product from this company. Called customer service said due to Covid no customer service available when online and receive no customer service no refund no product no help
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from N SYRACUSE, NY
- Parts Used:
- WP12656018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dropped a jar onto the pantry and broke the plastic piece on end cap that moved the drawer lid.
Removed the lid and pantry drawer. Removed crisper drawer on right side and glass shelve. Removed 2 screws on glide. Removed 2 nuts with nut driver. Gently tugged on the pantry end cap and it released from the back wall. Had to rotate about 90 degrees to remove the extension off the back wall so I could remove the thermostat control arm from old piece and put it onto the new piece. Gently removed the thermostat control through a series of squeezing pieces and rotations. Do not force anything. Take your time as you are working with plastic that could break at any moment with force. Replace in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neil from E GRAND RAPID, MI
- Parts Used:
- WP12656018
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Bottom drawer access door hinge pin broke of pantry end cap - right side. The pin(knob) is a molded part of the end cap.
Removed two 1/4" screws from the end cap with the nut driver and removed it. Transferred a few pieces from the old end cap to the new. Reinstalled the new end cap and presto, job complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from RICHMOND, IN
- Parts Used:
- W10827015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Door on the pullout lower "Pantry" had cracked
Part was pretty ubiquitous so plastic door pins part fits a lot of refrigs, no tools necessary, new part is flexible enough to bend slightly to fit over pins at side. Mine was a bottom freezer type.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Winchester, IN
- Parts Used:
- W11024089
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Refridgerator was not cooling as cold as normal
Removed the freezer door, by loosening 4 screws and pulling upwards to disengage door from frame. Removed the top basket by pulling up on both slides on the gear shaft sides, note they have retaining tabs you must push in. once the slide / guards are up the top basket comes out. Remove the bottom basket. Remove to angled screws on the top tracks and remove. Remove 6 screws on bottom slides, 3 per side and slide out as a whole unit. Unplug the ice maker, remove 3 screws for it to come out. Note I cleaned mine while it was out with vinegar to remove the mineral build up on it. Remove the screws in the back panel, and pull it forwards. The top vent has 2 clips that hold it in and you will need to remove it prior to fully removing the plate. The plug for the icemaker needs to be removed also. Pull the back plate out. Once the plate is out you can see the fan and access it. Unplug the clips that hold the wiring harness secure. 2 screws to remove the fan assembly. Once fan assembly is out, disassemble it, then reverse assemble it with new parts and fire it up. Mine took right off and running like its brand new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Grants Pass, OR
- Parts Used:
- WP12656105
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
I broke the pin that holds the lid that covers pantry at the bottom of the fridg.
I removed the drawers above and the glass shelf, then removedthe screws to remove the broken end cap then reversed the proceedure to install the new part. Was simple to do and it works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from ST CLR SHORES, MI
- Parts Used:
- EDR4RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
needed to replace water filter
unscrewed old filter, screwed in new....good to go!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from SHEBOYGAN, WI
- Parts Used:
- WP67006185
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Easy to take part out of the refrigerator.
Actually shouldn't you have included installation instructions with the product?
I had to search for installation instructions on Utube or the job would have ended in another cracked crisper frame.
I had to search for installation instructions on Utube or the job would have ended in another cracked crisper frame.
Was this instruction helpful to you?
Thank you for voting!