KBRS22KGBL3 KitchenAid Refrigerator - Instructions

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

Emptied freezer. Removed ice maker. Removed screws and back panel. UNPLUGGED POWER CORD. Unplugged wires to motor. Removed motor housing and replaced with new one. Reversed procedure to assemble.

I think spent more time removing the frozen food and cleaning the bottom of the freezer compartment than actually changing the fan.

it came in one well constructed assembly, fan motor and bracket - an exact match for the existing part. I did not have an ice maker to remove so the steps were pretty simple.

1) Remove ice cube tray holder
2) Remove about 8 screws that hold the condenser cover plate
3) Remove two screws that hold the bracket (fan is attached to bracket)
4) Pull bracket away and remove two green ground wire tabs
5) Remove power connector
6) Clip wire ties from bracket that hold power cable
7) Remove old part
8) Reverse procedure

The old part had some built in wire tie holders that held the power cable away from the fan. I had no problem using a normal wire tie to tie it out of the way. You can probably just fed it around without a wire tie and achieve the same results.

All in all a real easy job. I'd say the job was easier than replacing a door knob, but harder than putting on new wiper blades.

Should be no problem for someone with average handy man skills.

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

I first removed the icemaker pump and filler tube fron the back of the refrigerator by using an adjustable wrench and pliers. (very simple connection) I went ahead and replaced both items at that time.

Next I opened the bottom freezer and removed the top wire tray and ice container. I removed the bottom nut from the ice maker, pulled the electrical plug lose from the freezer connection. I then just lifted the ice maker upward and off the two screws on the side wall and out it came!

I had a little trouble with the filler tube as it came into the freezer. I had to go back and forth to the back of the refrigerator and freezer a couple of times adjusting the tube, so it woiuld clear the inside freezer wall.

This was a very minor problem. I feel like if I had followed the instructions and made sure the tube came through before attaching the icemaker it would have worked like a charm!

What I really liked, was everything was in the box for the job.

Removed timer kit (this was the second time for this part)/ replaced - this is a fairly simple job and take 5 minutes. The defrost thermostat take about 10 minutes to get to and take out the old one, replacement is a 2 minute job, unplug and replace, the longest part of this job is getting the back of the freezer off and then replaced, but it is fairly simple to do. Total time to diagnose about 15 minutes, replacement parts arrived in 2 business days, replacement time 15 - 18 minutes total. Recommend getting the thermostat and timer together. The first time this happened, only order the timer but I think the problem was the thermostat all along and the time seemed to be operating but when it came on every eight hours it tripped the circuit breaker Not sure which was really the problem, but all working fine now.

It was easy. I followed the video that was on the item page, and the installation went really smooth. Remember to heat the gasket up before installing.

removed cover in back of freezer and observed that defrost cycle seemed to happen too often. In comparing the existing part # with the factory part, I determined that possibly the wrong part was installed previously. (it had a 6 hr cooling cycle with a 45 min defrost...spec said I should be 8 hr cool & 20 min defrost) I did research on applianceguru.com... well worth the 5 bucks! I ordered a timer & thermostat & purchased a special refrigerator brush to clean the coils on the bottom. Cleaned the coils, replaced the parts in about 15 minutes and WA-LA! the freezer started getting really cold, but the fridge wouldn't get below 55. but it FELT cold! I swapped thermometers with the freezer & found out the thermometer was faulty!!! I now have the cool control backed down to 5/7 & freezer to 6/7. temps are freeze 0 and cool 40. works better than since we bought home 5 yrs ago! research & troubleshooting took a bit of time, but by the time I ordered parts I felt very comfortable I had the right parts. All said, cost me about 40 bucks instead of probably $200 from tech... schematics from partselect.com were very helpful as well!!

remove parts that were not need installed water valve , ice maker unit and hooked up water supply tested and it works fine. got the parts really quick Thank You

first I took the inside freezer panel off. Pulled off the deformed gasket. I noted how it was attached to the door. I then took the new gasket and placed it on the panel and reattached the panel to the freezer door. The screws are small and can get easily misplaced. Use a recepticle to hold the screws, it does make the job much easier. I also used a power drill which made the job move along nicely. Easy as pie. Thanks. I know where to get my parts in the future.

I took the cover off of the evaperator in the back of the freezer compartment and thawed the ice out with a heat gun. I then replaced the bimetal defrost timer I did have to change one connection as it would not plug into the harness.
I found the Defrost timer in the front of the refrigerator behind the filter cover at the bottom. Just one screw and a quick plug in and everything is working wonderfully. no more icing up

I removed the ice maker with 3 screws after having shut off the water. I tried getting the part locally but thought it was a bit much. Of course after having had ordered the wrong part, PS51041 and having it over nighted here and paying the return shipping I would have saved money getting it locally. When I finally got the right part I used the power cable and level lever off the old maker and reinstalled the ice maker in just a few minutes with a nut driver and screwdriver. Thurning on the water in about and hour it started making ice. When ordering online make sure you can get a large enough diagram to see what you are getting. If you can't ,call their phone number ant talk to a live person.

Remove 3 screws, took top hinge out, fz door and inserted shim...done.

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.