36358892896 Kenmore Refrigerator - Instructions

replaced water valve for 50 dollars, saved about 200 dollars by doing it myself

Vacuumed the area around the compressor, removed the PTC relay switch cover, pried the broken relay switch off the unit with a screw driver and replaced with the new relay switch. Replaced the backing of the refrigerator and tested, within minutes the work was confirmed.

There is no access to the inside of the door to replace the water line. I was able to insert a 1/4" drip line barbed connector into the old line at the base of the door and then connect that to a piece of the plastic tubing which I then connected back to the original water supply tubing with the 5/16" union. It took three attempts to get the tubing through the bottom hinge without a crimp in it. It's best to have a second person to hold the door while you "fish" the tubing through the hinge.

Removed the ice maker from the freezer. Removed the switch. Tested the switch with a multimeter. Ordered a new switch. Replaced it in the box. Installed the ice maker ( 3screws and electric cord plug. It works. Details available on the internet.

This part (plastic tubing) does not show up under my model of refrig...so I had to look thru the various water lines and pick the one that "looked" right. Luckily, this is the exact replacement part and works perfectly. I removed the lower back panel from the fridge, removed the bracket holding the water line connectors and pressed the outer ring of the coupler up until it released the old water line. I pushed in the new line, made sure it was snug with a gentle pull and ran the line under the fridge up to the existing coupler. I removed the old line from the existing coupler under the front left of the freezer door, and pushed in the new line. I did not need to use the new coupler. If my old line would not have been so brittle and cracked in several places, I could have just cut out the leaking portion and popped the new couple in to mend the line back together. Easy job and we can stop buying bottled water at the store now!

Replaced the actuator rubber and back plate holder

Unplugged frige, removed top shelf, pulled broken fan blade off. Replaced with fan blade just purchased from PartSelect. Very simple repair. Orderd and recieved the right part.

We had to empty the freezing section, remove the 4 screws that held the back panel and defrost the coils. Then with the diagram we got from the internet, we removed the defroster and easily installed the new one and put the back panel back on. We did find later that it was still icing over so I ordered the thermostat and we installed it today.
It too was easy to install. We spliced the wires and hooked the new thermostat to the old wires and reinstalled the back panel. Hopefully this will solve the problem for us now.

Total time to replace both slides was ten minutes. It took me longer to take the stuff off the shielf than it was to fix the slides!

When it was discovered there was a cooling problem in the refrigerator, I went to parts select web site and went through the troubleshooting section. Then I tested the defrost timer and the defrost element as directed by the web site. I then found out doing this, that is was the defrost timer. I ordered the part online and it was delivered THE NEXT DAY! I removed the bottom panel of the fridge, removed the screw holding the old timer, removed the wires, and reversed the procedure to install the new one. It has been 1 week, and everything is working great. Thank you PartSelect.
I have since then recommended you to a relative who was having the same problem. Thanks again.

Ordered the replacement parts-both water valves, printed the schmatic, then removed and replaced both parts. Was fairly straight forward, rmeember to unplg the fridge before you start. Problem solved, should be good for another 10 yrs.
Hard water prob caused the corrosion. Also replaced the water hose while I was back there, water tastes 100% better.

Tube was too short so I used the union to attach additional tubing to reach the valve at the lower rear of refrigerator

Ordered the icemaker replacement. unplugged the unit, followed the simple instructions and got it done in less than 30 minutes. It did take a LONG time to start making ice. But it's working now.

First, I moved the refrigerator out from the wall, unplugged from the electrical outlet, disconnected the copper tubing to the refrigerator, removed screws holding the cardboard backing, removed the nuts holding the assembly to the refrigerator and pulled it out. At that point, I disconnected the tubing units and wiring connectors from the assembly one by one attaching to the new assembly as I went.

However, this was not possible in the case of two wiring connectors. Evidently, the replacement part was made differently than the original. I had to rewire the replacement part as it allowed and then put the reconnected assembly back in place. I then placed the cardboard panel and reattached the copper tubing. Everything is working and no more leaks!

Pulled new tubing to the tank and put a union about 8 inches down from tank to new tubing. Great repair. Parts not readily available locally.