25337840890 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Bart from goldsboro, NC
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the compressor capacitor overheated
it was great. I ordered the capacitor for my frigidaire frig and it arrived
in 3 days. plugged in the part to the compressor and my frig has been
working ever since. I spent 3 minutes ordering the part and 30 seconds
attaching it to the frig. Easy, very easy. saved myself a 75 dollar repair
visit. thanks
in 3 days. plugged in the part to the compressor and my frig has been
working ever since. I spent 3 minutes ordering the part and 30 seconds
attaching it to the frig. Easy, very easy. saved myself a 75 dollar repair
visit. thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- wilson from indialantic, FL
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
compressor not running
thanks to all of the people who had the same problems I was able to make a quick fix on my fridge. I pulled the back cover off and found the compressor not kicking on so I replaced the start cap. and im back in bussiness.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Albuquerque, NM
- Parts Used:
- 5303281398
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No problems at all.
Very EASY!! just unpack, wash, and place into slots above crisper doors. A child could do this.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jerry from petaluma, CA
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
refer quit cooling and so did freezer
I replaced the defrost timer,defrost thermostat,and run cap.as it turned out the compressor went bad. I dont know the model because but the time I got this review I replaced the refer with a knew one . two weeks living out of coolers was so much fun !!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KATHI from DENVER, CO
- Parts Used:
- 218971202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
plastic part was broken
Decided to clean the refrigerator at the same time as replacing the broken part. Took shelf out, removed glass, washed all parts, removed broken rail (two screws) and replaced new part. Piece of cake!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clifford H. from Lakeland, FL
- Parts Used:
- 215473602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
shelf end caps broke, needed replaced.
I watched the video from your company and within a couple of minutes replaced them. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from BRILLION, WI
- Parts Used:
- 218971202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Left plastic rail broke and drawer falls out
remove two screws with a phillips screw driver and replace part in same fashion. Easy 5 minutes. Part arrived next day with regular mail. Surprised!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RUTH from AUSTIN, TX
- Parts Used:
- 218396700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replace the handle mount
When I was moving the refrig. handles from one side to the other...I broke one of the mounts. It was SO easy to order from this place, and they ship IMMEDIATELY. Second time I have used them, and am VERY impressed.
Was this instruction helpful to you?
Thank you for voting!
refrigerator door shelf endcap was broken.
Watched your excellent video online and made the repair just as your technician demonstrated....took about 1 minute!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Bucksport, ME
- Parts Used:
- 218971302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Front of hanging rail was broken and often slipped
Having looked at the broken area, in some frustration, for several years, I had a good idea how it all went together: the front end slips over a metal lip suspended from the front of the shelf above, and the rear is held in place by a single screw (single slot with hex-dead). The most time was taken clearing the items off the shelf above. Having done that, the shelf was easily lifted up and removed. Flip it over to expose the screw at the back. Remove that screw and discard the old/broken hanging rail. Slip the front end of the new rail (carefully) over the metal lip. At the rear, line up the hole on the hanger with the hole in the mounting bracket and re-insert the one screw. Re-install shelf and slide the drawer back into place on the hangers. Good to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Annie from West Plam Beach, FL
- Parts Used:
- 5303281398
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Glass Shelf
1) Remove glass from shipping Container. 2) Using fingers, place glass ever so gingerly in the shelf tray. 3) Pour a glass of wine to celebrate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ronald from deering, NH
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
freezer would not freeze longer than one day. after ten years without problem
pulled out freezer, went to floor,reached in next to compressor pulled off clip just like on the video.Pulled off old capacitator took off wire leads.Installed new one. Freezer runs great.Loaded it up with beef pork and venison. No problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne T from Galway, NY
- Parts Used:
- 5303917954
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Freezer was not defrosting thus refrigerator was not cooling
1. Unplug the refrigerator.2. Remove the storage rack and back panel in the freezer. 3. Locate the thermostat. 4. Defrost the freezer coils , i used a hair dryer. 5. Remove the thermostat from the cooling coil and then clip the connecting wires close to the unit. 6. Strip the ends of these wires and connect these wires to the wires of the replacement unit using the supplied wire connectors. 6. Heat seal with a lighter the connections using the water shield sleeves provided and further wrap connections with electrical tape. 7. Reconnect the thermostat to the cooling coil at the location it was removed from. 8. Replace the freezer back panel removed earlierand the storage rack if you have one. 9. Plug the freezer back in. My refrigerator has been working ever since the repair. There are several YouTube videos available that walk you through the diagnoses and repair process. They are very good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Wapella, IL
- Parts Used:
- 5303207345
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench set
door gasket was broken , sweating and dripping water on the floor
I took the freezer door off took center hinge out , took frig door off , unscrewed inside panel took off old gasket , put the new one on , put inside panel back on , (be sure the flange on the gasket stay's in the groove when you screw it back together) replace doors and anything else that needs replaced ! check the seal !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Goldsboro, NC
- Parts Used:
- 5303917590
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench set
Deforst Drain Pan rusted out
The old drain pan had a 1 ½” tall bushing attached to the center of the pan. The new pan did not have this bushing which was great. I had to cut about 1 inch off the bushing to remove the old pan. Also after cutting the bushing I had to screw the bushing off after cutting the old pan from the bushing. I installed new pan onto the ½” of threads that was left on the top of the compressor. Checked repair two days later all was great.
Was this instruction helpful to you?
Thank you for voting!