79571604014 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from PENNSVILLE, NJ
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Switch stops working
Replace with new switch. this is the third switch i have replaced in 10 years. the only part, besides a light bulb, that has gone bad. obviously this is a problem with this model for Kenmore, or just poor switch design.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MIKE from ATLANTA, GA
- Parts Used:
- AGU75188619
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Spring on old mullion fell out
Replaced with new mullion
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sonya from VAIL, AZ
- Parts Used:
- AGU75188619
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The spring on the mullion door broke for the last time
This was an incredibly easy repair! 1 phillips screwdriver and two screws. Disconnect the small adapter, and you are good to go!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from DADE CITY, FL
- Parts Used:
- MHY62044106
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Left French Door would not close properly
Removed two screws from door and three locking brackets with a small common screw driver. Raised the bracket, slide in the spring, held down the bracket, installed screws and plastic covers. Less than 2 minutes. Easy application no problem with the new spring or ,mullion..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from MONTGOMERY, AL
- Parts Used:
- AGU75188619
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Spring broke on Mullion
Watched the video. Took the screws out, unplugged the connection and slid mullion off. Then plugged the new one in, slid it on and attached the two screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- shirley from ONALASKA, WI
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Light switch for refrigerator not functioning
Followed instructions online
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BRENT from RENO, NV
- Parts Used:
- AEC73877602
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
Wrong parts sent twice. One of the parts was a substitute 2" too long
Unable to complete repair, had to send parts back
Part should have been PS11732074, but got PS11732704- wrong part
This was a substitute part and was 2" too long
Waiting for refund on this part. It cost me $14.50 to return it by UPS!!!
Part should have been PS11732074, but got PS11732704- wrong part
This was a substitute part and was 2" too long
Waiting for refund on this part. It cost me $14.50 to return it by UPS!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from ELLWOOD CITY, PA
- Parts Used:
- MHY62044106
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The original spring in the mullion door broke
I disconnected the refrigerator power, removed the 2 screws holding the mullion door on the left side of the refrigerator French-door (it’s the flap that allows the door to close). Removed the broken spring and installed the replacement spring in its place. Reinstalled the mullion door by putting it in place and installing the previously removed screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathryn from Albuquerque, NM
- Parts Used:
- ACQ86549505
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
The cover had cracked
1. Remove all food from the shelf and take out the crisper drawers.
2. Remove the glass and take out the crisper frame.
3. Take the screws out of the frame that are holding the cover frame in place and remove the old cover frame..
4. Install the new cover and replace screws.
5. Re- install the drawers and glass.
( I'm a 76 yr old female and did it myself with the help of the instructions you provided!). Thanks
2. Remove the glass and take out the crisper frame.
3. Take the screws out of the frame that are holding the cover frame in place and remove the old cover frame..
4. Install the new cover and replace screws.
5. Re- install the drawers and glass.
( I'm a 76 yr old female and did it myself with the help of the instructions you provided!). Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from IMPERIAL, CA
- Parts Used:
- AGU75188619
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken spring on flapper door
Unplugged the frig and removed two phillip screws on flapper door of left door... Unplugged the electrical connector and removed flapper...
Picked up new flapper and snapped electrical contractor together... Slid new flapper bar into place and inserted two phillip screws... Job complete in 15 minutes...
Picked up new flapper and snapped electrical contractor together... Slid new flapper bar into place and inserted two phillip screws... Job complete in 15 minutes...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Ashland, MA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Lights didn't come on when door was opened
I have moderate to good mechanical skills, but getting the old switch out was a sizeable challenge. Since this switch suffered some damage during extraction, I was lucky to have ordered a new one to replace it. Reinstall took approximately 90 seconds. PartSelect saved me an expensive service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from FALL RIVER, MA
- Parts Used:
- 4620JJ2009A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door Stopper had snapped off
Unscrewed what remained from broken door stop, aligned new one, screwed it in. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from TONAWANDA, NY
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bad switch
The 2 minute or so video was not exactly matching the model that we had but the instructions were very good and important. The switch was a little difficult to get out from the side of the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from STEPHENVILLE, TX
- Parts Used:
- EBS61443363
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken freezer rail.
Took out tray , removed 2 screws, removed old rail and installed new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JON from OJAI, CA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
INTERIOR DOOR ACTIVATED LIGHT SWITCH QUIT WORKING
1. Unplug the refrigerator (to avoid shock) 2. With one screwdriver pry open the switch on the side facing the door to a gap of about 1/8 inch 3. Insert a second screwdriver into the gap to press the plastic tab back slightly and this should release the part. 4. pull the part out and unplug it, you may have to pry back some small tabs on the sides, 5. Plug in the new switch 6. plug in the refrigerator the light should come on, if not tighten the connection 7. Insert new switch back into its slot, it should snap in place. Done!
Was this instruction helpful to you?
Thank you for voting!