59679533017 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from BRUCE TWP, MI
- Parts Used:
- W10830162
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Gasket has 2 tabs on the side that opens. Both had torn. Also one vertical slit halfway up the gasket
Followed your instructions: gasket came coiled in the box and was slightly curled up. Both left & right side of gasket were linked. Followed your instructions to properly restore the shape. Pulling the old gasket off and installing the new one took just a few minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from WAKE FOREST, NC
- Parts Used:
- W10884390
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Existing icemaker would freeze up, stop making ice.
I did not unplug the refrigerator. Your choice on this. Take a close look at the existing icemaker, how the wires are routed and what the water spout looks like as it relates to the icemaker. Small flat-blade screwdriver will help in unlocking tabs on the icemaker plug. Go ahead and unplug it. Of the three screws that secure the icemaker, two are impossible to see without holding a mirror in your third hand. Completely remove the bottom screw (by feel). Don't drop it, like I did. Have no idea where it went. Loosen the top two screws but do not remove. Icemaker will lift off of the top two screws when you push it up. With old icemaker out of the way, plug in the new icemaker. Be careful to properly align the water spout into the new icemaker as you hook it on the two top screws. When everything looks good, tighten the two top screws. Replace the bottom screw, if you didn't lose it. My icemaker is doing fine without a bottom screw. It should make some ice within an hour, or so. Mine did.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David L. from Red Rock, TX
- Parts Used:
- W10874836
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The orignal proberm was broken hinge on End Cap
There was little or almost nothing to change out the End Cap, two screws on the End Cap and two screws on slide. It took longer to removed and replace the two drawers and shelve than it did to replace the End Cap. The part I ordered was exactly what I needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Duncan from Metairie, LA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The Switch Broke...Absolutely Fell Apart.
I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JimBob from CRAWFORDSVLLE, AR
- Parts Used:
- W10884390
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Bottom freezer ice maker quit making Ice
Used a deep well 1/4" nut driver. Loosen 4 screws on inside of door and slip it up and off rack. Remove 2 screws on bottom of ice maker. Loosen top 2. Slip up of screws, unplug ice maker and remove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from CASTLE ROCK, CO
- Parts Used:
- W10884390
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
icemaker stopped working
Hardest part is access to the icemaker itself. Once I removed the freezer door (bottom drawer freezer), and got the sliding basket out, it was a 10 minute job. Make sure you start the upper screws first, the icemaker will hang there while you adjust, connect the harness, and tighten. Make sure you are ready before you close the door, it will start making ice as soon as the door is closed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from RIVERSIDE, CA
- Parts Used:
- 8009
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
light bulb in water ice freezer door went bad
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Geraldine from MUNDELEIN, IL
- Parts Used:
- W11395888
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Did not need filter
Unscrew filter. Screw on filter bypass
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from WESTERVILLE, OH
- Parts Used:
- W11658402
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Broken black plastic spring mechanism inside freezer rail
Remove rail and removed broken black plastic spring mechanism with new one and then replace rail.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicole from BUFFALO, NY
- Parts Used:
- WPW10284685, WPW10284684, W11658402
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The freezer door wouldn't stay closed
Replaced the rail and slide baskets. Also readjusted the basket. This was extremely easy and saved me close to $500
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Manchester Center, VT
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Refrigerator light would not stay on
Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.
reassembled the pieces.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from Fountain Inn, SC
- Parts Used:
- W10874836
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Peg for the Deli Drawer Lid BROKE - right side
Honestly, so simple . Removed the fruit / veggie drawers, glass shelf and the supports for that shelf. Couple of screws and nuts and it was off. As stated before... the most "thought goes into attaching the linkage for the temp adjustment on the right side . GREAT opportunity to CLEAN the up the fridge a bit!! Parts Select made this such a no brainer. Their Customer Service was really an added bonus!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from CHERRY HILL, NJ
- Parts Used:
- W10830162
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
old gasket with holes
Top bottom then sides took about 15 min
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sonny from WHITESTOWN, IN
- Parts Used:
- WPW10300025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Ice maker not making ice.
Removed old ice maker by removing 3 screws, unplugged wiring harness. Replaced with new ice maker, placed three screws back to secure the ice maker, plugged wire harness back, and product is working well at this time.
Was this instruction helpful to you?
Thank you for voting!
Broken Right Hinge
Parts delivered quick. 15-20 minute repair time. Just needed to remove a few shelves, then screws to remove damaged parts and replace with new. Very easy repair.
Was this instruction helpful to you?
Thank you for voting!