59679532016 Kenmore Refrigerator - Instructions

Remove broken parts with philips screw driver (6 screws). Replace encaps while attaching pantry drawer lid. Insert center rail and new drawer.

.screw held in the center of the rail,pull it out,slide the rail up off the support brackets on the door,unplug the old one & plug in the new one,slide on, & replace the screw! That Easy

Ordered new fan motor
Got part took fridge apart
Result was the motor was running
The fan blade had come off the motor
Replaced the motor anyway and reinstalled the fan, working well

I was getting small sections of ice and a snow like build - up around the freezer door. I thought that the door was not sealing tight enough and that the cold air was leaking out. The original door gasket appeared to not have any flexibility anymore and was getting hard. I ordered a new door gasket from PartsSelect. When the gasket arrived it was in a large enough box and that saved me some time as the gasket was not "crushed" to the point where there were a lot of kinks in the gasket. I used a hair dryer on low to warm the gasket and stretch it out some. The freezer door required me loosening four small screws and lifting the door off. I placed the door on an old blanket so not to scratch the finish. It was easy to remove the old gasket and after doing so I cleaned the track where the new gasket was to go with isopropyl alcohol, Once cleaned, I placed the gasket over the channel in the door where the old gasket had been and started installing the new gasket. I started at the corners and you can feel the gasket snap into place. Once the four corners were done I started at the top and installed the gasket the rest of the way. You can feel it snap into place. as you work your way around the gasket channel. Once the gasket was in place I placed the door on the four small grooves where the door had been and tightened up the screws. I made sure that no white from the inside of the freezer door was showing after the gasket was in place and that the gasket had some "spring" to it. The door was back on, the gasket was tight and it appeared to be a good seal. Around 12 hours later I checked the freezer and there was no more ice or "snow" on the edges of the freezer. While the gasket was not inexpensive, it is a genuine OEM piece, and the gasket is a lot cheaper than a new refrigerator!
I hope this was helpful...

This is a bottom freezer refrigerator. Had to remove the freezer door and bottom shelve to make access to the ice maker possible.. Removed the old ice maker using a 1/4" nutdriver to loosen, but not remove, the top 2 screws. Removed the bottom support screw completely.. Detached the wiring harness from the freezer connector and lifted the ice maker up and out of the freezer. Installed the replacement ice maker in reverse order, slipping it over the loosened top screws. Tightened them, making sure the usit was level, then inserted and tightened the bottom support screw . Plugged the wiring harness into the freezer connector.. Unit produced ice within 3 hrs. .

Replaced the rail and slide baskets. Also readjusted the basket. This was extremely easy and saved me close to $500

1. Turn your water OFF and pull the refrigerator out from the wall so you can access the back.
2. Use pliers to remove tubing clamp.
3. Remove old water fill tube.
4. I used a putty knife to gently pry out the old fill tube from the back of the refrigerator. Once the fill tube pulls out about 1/4 to 1/2", then you can gently pull the remainder of the tube out by hand. Once I removed my "old" fill tube, that is when I saw the "ice plug" that was causing pressure in the water supply line and caused my water line to pop off.
5. Install new fill tube. The end that goes in first needs to go through a small "ring" inside the freezer (this "ring" is not encountered until the fill tube only has about one more inch to be inserted into the back of the refigerator. I could barely see this "ring" if I opened the freezer drawer and stuck my head in as far as I could. I had to gently rotate the new fill tube until it cleared the "ring". You will feel some resistance until it lines up properly.
6. Snugly push in the part that stays on the outside of the refrigerator until it looks like it is sealed.
7. Gently push up the water fill tube where it belongs in the new part and replace the tubing clamp.
8. Turn your water on and make sure there are no leaks (I left my refrigerator out for about an hour).
9. Push your refrigerator back in place.

It was quit simple. I removed the draw and the shelves above the pantry unit. Once everything was removed (2min), I removed the one side pantry bracket ( 2 screw's). Put in the new pantry bracket and screw's and I was done. I'll give it ten minutes total. easy button Thank you

Very simple--Just remove all drawers, remove old end cap, remove slider from old end cap and put on new one. Screw on new end cap and replace drawers. Took about 10 minutes.

Removed old seal and installed new one. Whole job took less than ten minutes. Repair video made it very easy to do! Be sure to allow proper relaxation of new seal before install.

Removed the old gasket by pulling it out of the groove and installed the new gasket using my fingers to push the gasket into place.

First, I took out the glass tray along with the two slide out compartments that are part of that assembly. Then I used a small socket set to take out the three screws that hold the part in place and along with the part a plastic connector comes out with it that adjusts the temp of the bin area. Line up the holes on the slider and two screws come out that hold the slider to the part. Disconnet the plastic piece in the back that adjusts are flow (press down plastic holders) Reattach the slider, snap the plastic piece on the back and reassemble. Sounds complicated but once you are in there, its self explanatory.

Honestly, so simple . Removed the fruit / veggie drawers, glass shelf and the supports for that shelf. Couple of screws and nuts and it was off. As stated before... the most "thought goes into attaching the linkage for the temp adjustment on the right side . GREAT opportunity to CLEAN the up the fridge a bit!! Parts Select made this such a no brainer. Their Customer Service was really an added bonus!!

We removed the old switch, unplugged it, plugged the new one in and it was easy to do. But when we tried to put the switch back in we had a very hard time doing it. Eventually got it in, but if it had not been for the difficulty we had getting the new switch to snap in to place, it would have taken under 5 minutes.

Took out the bottom drawer, removed one hexhead nut on the unit, unplugged the unit, plugged in the replacement unit, screwed in the hexhead screw, replaced the drawer, that's it! Very user friendly.