59679243018 Kenmore Refrigerator - Instructions

Reviewed replacement instructions video on your website. Just followed the easy instructions to pop out old cover and pop in new cover. I would not have tried to replace it myself had I not seen your video. Super easy.

Ordered the part. When came in I took it out of the box and slid the two end posts into the provided holes. Lid fixed in less than 5 minutes. Part came in on the third day because I ordered on Friday afternoon.

Took out the old and installed the new.. The fit was perfect.

Popped off the control panel at the top behind the door. Found the thermistor and replaced it, cutting the wires and splicing the new one in. Immediately the warm section of the refrigerator was getting below freezing temperature readings, so the cooling vent was not opening. I put the old one back on and the temperature readings went back to being accurate. So this was not the problem. I believe now that the fan somehow is not blowing enough cold air up. So now I'll probably buy a fan motor and maybe a blade and try that. Otherwise the computer module I priced at $500 so I hope it isn't that. I replace the fan motor a few years ago already.

first of all,i just want to thank parts select for sending me a second ice maker at no charge.after installing the first one and it didn't work,i talked with Heather and she sent me a new one.installation went the same as before.hardest part is getting the quick connect wire harness apart and the ice fill arm .it is working great and my home is happy.thank you!

Customer service provided a video of the ice maker removal and installation. I watched the video and performed the remove and replacement.
Simple task.
Shout out to the customer service person, OUTSTANDING SERVICE. I apologize for not getting her name, great job.

Since there were no instructions, I was a tad hesitant but dove in. I was just replacing the right end cap, not the left. Removed the involved shelf as well as the two drawers above. Undid the three screws involved and carefully removed the slide rail end cap as well as a part in the back that was attached. That was the hairy part. It took a bit of time to remove it since everything seems so brittle but I was careful and got the assembly out without breaking anything. Also had to remove the slide rail and humidity control. Nothing to removing and replacing the slide rail. You just have to put it back correctly oriented. This was easy. I just looked at the one on the left, which I hadn't removed. Most time consuming part was cleaning things that were normally inaccessible, before re-installing.

I didn't. Don't know how to get to light bulb to change it for this specific model

Remove rail and removed broken black plastic spring mechanism with new one and then replace rail.

I contacted partselct to see if I could get the end caps with new hinges to correct the problem. My customer service contact was very professional and a huge help in helping me select the correct parts. When the parts arrived I was amazed they were genuine whirlpool parts, fit perfectly, and were easy to install. I have other parts to order and will use partselct again. I appreciate everything they did for me to solve this problem.

Removed old ice maker. Unscrewed unit from slide. Unplugged old wire. Screwed on new unit. Replugged in wire. Slid ice maker back into refrigerator and all worked properly.

Unscrew filter. Screw on filter bypass

The part came the next day, very quick. The wrong size ended up in box we recieved. The part # we ordered was correct, just a mix up in the packaging process. I called and the customer service dept. had a new correct crisper pan delivered to my door two days later. Even with the mix up it was very fast and a good price compared to other sites. I would order again in the future.

Very easy. Just get hold of the gasket with your strong fingers and pull it out of the groove it is in. Clean the groove, I used Windex and paper towels. On the new gasket there are 2 wide areas on the vertical part. these must be facing toward you and on the handle side of the door. start at the tor center of the door and work the gasket in with your fingers outward to the corners then work on the bottom of the gasket in the same manner, then start on the vertical gaskets. when you think every thing is aligned take your thumbs and press very hard all around. You may have to repeat.

Layer it out for 24 hrs used hairdryer on med for the wrenkles.