59679542015 Kenmore Refrigerator - Instructions

Remove rail and removed broken black plastic spring mechanism with new one and then replace rail.

Remove broken parts with philips screw driver (6 screws). Replace encaps while attaching pantry drawer lid. Insert center rail and new drawer.

Unscrew filter. Screw on filter bypass

one screw and electric plug and the unit slide out. Slide the new one in and your ready to go.

Very simple--Just remove all drawers, remove old end cap, remove slider from old end cap and put on new one. Screw on new end cap and replace drawers. Took about 10 minutes.

First, I took out the glass tray along with the two slide out compartments that are part of that assembly. Then I used a small socket set to take out the three screws that hold the part in place and along with the part a plastic connector comes out with it that adjusts the temp of the bin area. Line up the holes on the slider and two screws come out that hold the slider to the part. Disconnet the plastic piece in the back that adjusts are flow (press down plastic holders) Reattach the slider, snap the plastic piece on the back and reassemble. Sounds complicated but once you are in there, its self explanatory.

It was quit simple. I removed the draw and the shelves above the pantry unit. Once everything was removed (2min), I removed the one side pantry bracket ( 2 screw's). Put in the new pantry bracket and screw's and I was done. I'll give it ten minutes total. easy button Thank you

Replaced mullion and pivot block
The pivot block and the mullion showed signs of wear and tear where they would meet up to close the left door.

Parts delivered quick. 15-20 minute repair time. Just needed to remove a few shelves, then screws to remove damaged parts and replace with new. Very easy repair.

Took out ice maker. Then unscrewed tray after opening old turn motor clock panel and carefully detaching wires from socket(s) where needed. Put in and screwed in new tray with the new motor clock. Replaced wires into new sockets. Put the whole maker back into place. Makes great ice.

Placed new gaskets on hot patio to smooth them out. Took minion bar off and removed door gaskets. Replaced new gaskets, and minion bar.
Took freezer door off and replaced gasket. I had problems with the first set of door gaskets but customer service replaced them in record time. Service was outstanding. 5 Stars

Honestly, so simple . Removed the fruit / veggie drawers, glass shelf and the supports for that shelf. Couple of screws and nuts and it was off. As stated before... the most "thought goes into attaching the linkage for the temp adjustment on the right side . GREAT opportunity to CLEAN the up the fridge a bit!! Parts Select made this such a no brainer. Their Customer Service was really an added bonus!!

For this repair, the following YouTube video was most helpful in showing how to remove the ice maker from the refrigerator model that I have: for some reason this site has deleted my video cite but it is the YouTube video cite that ends in 7HHH03SFdCA Next, because the electrical wiring harness part has changed since production, and the new ice maker part comes with two different harness' (you have to determine which one is most similar to the harness that you remove), take a lot of pictures of the old wiring harness before removing it. There are a lot of different wires that need to be reconnected. There was a prior post by "Greg from Aliso Viejo, CA" that I printed out and followed--that post was also very helpful.

I removed and disassembled the broken frame. I cut a six inch piece of coat hanger and folded in half and crimped together. Then I took pliers and made a hook that I hooked into the metal strip in the back of the refrigerator that holds the upper shelves. After replacing the frame, center rail and glass I bent the wire up under the back of the frame to provide a support. The back of the frame is weak and has no center support.

Remove back cover
Remove drip thing from top to tray in the back
Remove fan motor assembly. This is squirrely. Top bends towards you, bottom pushes in to the unit. Not fun.
CAREFULLY remove copper tube that rests on drip tray
Remove tray - there are clips in the front that get released by screwdriver
Clean up
Replace new tray
Replace copper tube
Play with fan motor assembly till it fits. It doesn't look like it's gonna work until it does. See youtube videos on this.
Replace drip thing from top to tray - I forgot this one the first time.
Replace cover.

This is a simple, but squirrely, repair. Right on the border of easy (because so few tools and steps) and A Bit Difficult because of the patience required.