59673503201 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Harold from Oakton, VA
- Parts Used:
- D7824706Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Refrigerator Ice Maker stopped making ice.
(1) Removed the three screws which attached the ice maker to the freezing compartmnet wall in refrigerator; (2) Disconnected the power to the old ice maker; (3) Removed the old ice maker from the freezing compartment of the refrigerator; (4) Took the white front cover off of the old ice maker; (5) Disconnected the wiring harness from the old ice maker; (6) Removed the "ice making-stop arm" from the old ice maker; (7) Placed the items taken from old ice maker on to the new ice maker; (8) Reconnected the new ice maker to the power; (9) Placed the new ice maker in the proper position in freezing compartment of refrigerator and replaced the three screws. JOB DONE!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mike from holly springs, NC
- Parts Used:
- M1205302, WP10450603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Left front plastic wheel was broken
Pop loose the plastic grate at the bottom.
Locate and remove the wheel leveling screw from the front bottom corner.
Remove cotter pin from the pin that mounts the wheel assembly to the refrigerator. Tap out the mounting pin.
Lift out the wheel assembly.
Remove the Roller pin from the wheel assembly. I used a Dremel tool with a cutting disk. A hack saw will also probably work.
Install the new roller pin and wheel into the wheel assembly. Use a hammer or vice to peen over the end of the roller pin.
Reinstall and adjust wheel assembly.
Locate and remove the wheel leveling screw from the front bottom corner.
Remove cotter pin from the pin that mounts the wheel assembly to the refrigerator. Tap out the mounting pin.
Lift out the wheel assembly.
Remove the Roller pin from the wheel assembly. I used a Dremel tool with a cutting disk. A hack saw will also probably work.
Install the new roller pin and wheel into the wheel assembly. Use a hammer or vice to peen over the end of the roller pin.
Reinstall and adjust wheel assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phil from GREENFIELD, IN
- Parts Used:
- W11395888
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Remove the water filter to install the bypass cap
Lower the filter bottom housing to gain access to the filter. Unscrew the filter and install the bypass cap. Secure the lower filter housing to the top assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Sumner, WA
- Parts Used:
- WP65889-4
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Fridge stopped working
I called a repair man from a pretty large name to come out and take a look. He found out in about 10 minutes that it was a bad capacitor. The quote he gave me was $75 for the part and $175 labor. I tried my best not to laugh and tell him no thank you. He did have to charge me for him to show up, which was only $98.
So I used what he told(minus the "scrap it") and opened it back up. Although he had left wires everywhere and the broken pieces laying inside, I thought it was enough for me to order the part. PartSelect was very easy to navigate and ordering was a breeze. Took about 4 days to get the part and I ordered in the X-mas craze. Fixed it in about 15 minutes.
So I used what he told(minus the "scrap it") and opened it back up. Although he had left wires everywhere and the broken pieces laying inside, I thought it was enough for me to order the part. PartSelect was very easy to navigate and ordering was a breeze. Took about 4 days to get the part and I ordered in the X-mas craze. Fixed it in about 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Long Valley, NJ
- Parts Used:
- EDR4RXD1
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Six months in use time to replace the filter
It is simple, unscrew the old screw in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angela from Bay Village, OH
- Parts Used:
- W10827015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cracked plastic on pantry drawer lid
Broken lid popped out, new lid popped in. No tools required. 30 seconds to replace. Great price, part shipped within an hour of placing my order and arrived the next day, although I only paid for standard shipping. Excellent service - will definitely order again if the opportunity arises!
Was this instruction helpful to you?
Thank you for voting!
Switch light didn't work; broken drawer cover hinge
I removed the switch assemble from the panel with a Swiss Army knife. Disconnected the two wires and reversed the process with the new switch. Not being all that handy, I assumed the job would be very involved, but was very pleased that it was nearly effortless. A less than 15 minute operation.
Removing the right side panel of the lower drawer was a slightly more involved, requiring the removal of 3-4 screws and replacing the inner workings of the temperature adjustment workings on the new panel. But it proved pretty simple and only required about 20 minutes start to finish.
Removing the right side panel of the lower drawer was a slightly more involved, requiring the removal of 3-4 screws and replacing the inner workings of the temperature adjustment workings on the new panel. But it proved pretty simple and only required about 20 minutes start to finish.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lori from Chuluota, FL
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
There was no light on in refrig area
Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one.
But Parts Select is a great place to order from. Thank you.
But Parts Select is a great place to order from. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene from Petaluma, CA
- Parts Used:
- W10827015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
A friend dropped a jar of relish on the plastic window and cracked it.
Easy repair. Unwrapped the new cover; pulled the old one off by releasing tabs. Inserted new piece.
Took less than 15 minutes. Looks like new. The replacement part arrived quickly from Part Select.
Took less than 15 minutes. Looks like new. The replacement part arrived quickly from Part Select.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Murphy, NC
- Parts Used:
- WP67003639
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Right hand door would not auto close.
Removed the top door hinge cover.
Remover the four 12mm hex screws.
Lifted empty door off bottem hinge support.
Removed old door closure.
Put some silicon lub on the new closure and installed.
Reversed the removal steps.
But this did not fix the problem. Will have to remove the door and inspect the inside of the door's lower hinge assembly.
Remover the four 12mm hex screws.
Lifted empty door off bottem hinge support.
Removed old door closure.
Put some silicon lub on the new closure and installed.
Reversed the removal steps.
But this did not fix the problem. Will have to remove the door and inspect the inside of the door's lower hinge assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda from Spokane Valley, WA
- Parts Used:
- EDR4RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace water filter
pop open, unscrew quarter turn, screw new one in quarter turn, pop shut. duh
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Newton Grove, NC
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light switch rocker broke, disabling freezer internal light, water dispenser, and ice dispenser
Very simple. Matched female plugs with respective male color coded prong; pushed together then inserted unit in slot of freezer sidewall and rotated into position...job done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rolf from Stanhope, NJ
- Parts Used:
- W10827015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken drawer lid
Removed broken lid and snapped new one in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from West Warwick, RI
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken light switch
followed the instructions provided and that's it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Garry from Anderson, IN
- Parts Used:
- 12002193
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
My ice maker was driping water on the ice cubes
It was really pretty simple. You get to the back of the frig, open a panel and the valve is right there. The instructions where clear on what to do, even though the new valve was different water line connections. It was spelled out what to do. Works great and all the parts supply places would have to ordered it anyway, so I saved $ and got the valve in 30 hours to boot. Thanks
Was this instruction helpful to you?
Thank you for voting!