10651113210 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- rich from PEMBROKE PNES, FL
- Parts Used:
- WPW10225581
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Top half of freezer & fridge were not cooling. Freezer fan had been making unusually loud noises.
Piece of cake. It took me longer to remove the food from the freezer, remove shelves and back panel than to do the repair. I heard the fan making some noises so I replaced both the fan and defrost thermostat. I used the instructions submitted by a another customer. My 20+ year old fridge is like new now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Camille from Glen Ellyn, IL
- Parts Used:
- WPW10225581
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Freezer was icing up and leaking. Refrigerator side would not keep cold.
We emptied out both sides, refrigerator and freezer, and followed the instructions in your video. We turned it off and disconnected the power. We took off the freezer door first. It made it much easier to get the shelves out and reach way back into the freezer. We removed the light and cover, then the ice auger motor. The back panel was easy to lift and remove. The wire assembly was a little hard to understand at first, but when we figured it out it was easy to remove and replace the bimetal defrost thermostat. We did check the video when we had the wire harness out, to make sure we got it right. We reassembled the freezer's inside parts and reattached the door. Before we turned the power back on, we scrubbed down the entire refrigerator. When we turned the power back on, the refrigerator and freezer were operating quietly - no sparks or explosions or shorting out - hooray! And the problems were solved.
The most important resource is your video. It looked like something we could do, and then ordered the parts. Our repair took a long time because we checked the video so many times. Thank you so much for the great information and the excellent parts. We could not have done it without you.
The most important resource is your video. It looked like something we could do, and then ordered the parts. Our repair took a long time because we checked the video so many times. Thank you so much for the great information and the excellent parts. We could not have done it without you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from STATEN ISLAND, NY
- Parts Used:
- WPW10225581
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Freezer work perfectly, Refrigerator Stopped getting cold, water line froze, there was ice Forming around the condenser in the bottom of the refrigerator behind the drawers
Freezer worked great, refrigerator stopped getting cold and lots of ice formed around the condenser on the bottom of the refrigerator.
First I had a serious ice issue, ice build up around the bottom of the refrigerator and all through the cold air vents, condenser and cooling fan. I unplugged of the fridg and let defrost over night. I also took all the cold air vents out and cleaned them.
Then I followed the switch install video very simple switch install. Now the Refrigerator works Great nice and cold.
First I had a serious ice issue, ice build up around the bottom of the refrigerator and all through the cold air vents, condenser and cooling fan. I unplugged of the fridg and let defrost over night. I also took all the cold air vents out and cleaned them.
Then I followed the switch install video very simple switch install. Now the Refrigerator works Great nice and cold.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from ENDWELL, NY
- Parts Used:
- WPW10225581
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Freezer Temp was -20 to -30 degrees F. and did not defrost because of the extreme low temperatures.
The Video on U tube was helpful. I have a side by side model and it was difficult to work in such tight quarters to attach the new part . I found that by removing the cable assembly it was much easier to attach (cut and crimp) the new part on the outside , then reinsert the assembly. The new part resolved my problem. Don't panic when you try and remove the cable assembly. Hope this is helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from SAN DIEGO, CA
- Parts Used:
- WPW10662129, WPW10197428
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Random clicking noise
The toughest part was pulling the refrigerator from the wall....After removing the back-bottom access panel the compressor is right there with the Start-Dev and Cap..Took a few min to remove and install new parts....Very Simple and works great...no more clicking..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from VANCEBURG, KY
- Parts Used:
- WPW10179146
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Inlet valve was broken at the water line connection
Changed inlet valve
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Liberty hill, TX
- Parts Used:
- 4388736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set, Wrench (Adjustable)
Ice Bin Auger Drum was broken.
First, I removed the 6 screws which hold the ice bin to the drum and the front cover. I then removed the screw which holds the door lever and bracket to the ice bin. Then I took the C clip and washer off the end of the auger to remove it from the housing. I removed the plastic nut to remove the auger drum from the auger shaft, being careful to place the blades on the table in the order they were removed. I then installed the new auger drum on the shaft and re-assembled everything in the reverse order. This was really easy for me because I had replaced the auger previously. (about 2 years ago)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elyse from Skokie, IL
- Parts Used:
- 4387478
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the light socket broke apart
I took out the old socket by moving a clip. Reattached the electrical wires, clicked in the socket and that was it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tammy from SHERMAN, TX
- Parts Used:
- WP2309941
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Shelf was broken on one side.
The repair was super easy. It took all of 10 seconds. From ordering the part to repair, I would use part select 100%! Excellent company with excellent parts. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kenneth from YORBA LINDA, CA
- Parts Used:
- WPW10710203
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Maximize door storage
Unpack, wash in warm soapy water, slide into pkace
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from JACKSONVILLE, NC
- Parts Used:
- WP1119017
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Ice deflector had broken.
Removed ice tray and unbolted front cover. Removed broken piece and snapped new ice deflector in place. Reinstalled front cover and put ice tray back into freezer. Cycled crushed ice, works great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HARI from STUDIO CITY, CA
- Parts Used:
- WPW10276348
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
THE SLIDE OUT SHELF WITH GLASS FRAMES WERE BROKEN.
I HAD TO BE CAREFUL...THE SHELF COST ME OVER $200/
iT WAS PACKED SAFELY AND THE GLASS SHELF ARRIVED SAFELY.
REMOVING IT FROM THE PACKING IS NOT TOO DIFFICULT...THE SHELF IS BROAD..
ONCE I WAS ABLE TO BRING IT OUT, I WAS ABLE TO REPLACE IT INTO THE REFRIGERATOR BY SLIDING IT INTO THE FRAME.
I AM NOT A HANDYMAN...BUT THIS WAS EASY.
iT WAS PACKED SAFELY AND THE GLASS SHELF ARRIVED SAFELY.
REMOVING IT FROM THE PACKING IS NOT TOO DIFFICULT...THE SHELF IS BROAD..
ONCE I WAS ABLE TO BRING IT OUT, I WAS ABLE TO REPLACE IT INTO THE REFRIGERATOR BY SLIDING IT INTO THE FRAME.
I AM NOT A HANDYMAN...BUT THIS WAS EASY.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from SAUGERTIES, NY
- Parts Used:
- W10864399
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Crisper shelf glass missing
Removed cheese & cold cut drawer accessing lower crisper drawer glass missing from surrounding frame.
Dropped in glass into grove of crisper frame…Reinstalled (sliding)!above cold cut drawer in its position and the same for crisper drawer..Finished!!!
All good except for $110.00 price tag for a piece of glass
Dropped in glass into grove of crisper frame…Reinstalled (sliding)!above cold cut drawer in its position and the same for crisper drawer..Finished!!!
All good except for $110.00 price tag for a piece of glass
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from WALDORF, MD
- Parts Used:
- WPW10276348
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My shelves had cracked and broke
Order new shelves
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claude from KLAMATH FALLS, OR
- Parts Used:
- WPW10178772
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Cracked crisper drawer.
Removed old drawer and replaces with new one. A perfect fit. E-bay advertised free shipping, but their price was higher than PART SELECT WITH THE SHIPPING CHARGE.
Was this instruction helpful to you?
Thank you for voting!