25372924016 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Glen from North Tonawanda, NY
- Parts Used:
- 240535001
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
no heat when drying
Replaced thermo-fuse
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Ft. Myers Beach, FL
- Parts Used:
- 5304469396
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
arm wouldn't go all the way down and dump ice
Took front off and found the broken spring, got new one and replaced, now works great. Make sure to unplug as the water can come on and flood the freezer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Berit from Kirkland, WA
- Parts Used:
- 240358007
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old rusted freezer shelf
removed the old rusted shelf and replace with new one. Very simple.
Was this instruction helpful to you?
Thank you for voting!
Dog aet the diffuser wile i was cleening the frig
Take down the light assembley by removing the 4 one qurter inch screws, and install the diffuser where it belongs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Gambier, OH
- Parts Used:
- 241559801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light socket burned out
snapped the wires from frig onto the proper prong and viola,it works. The proper prong is identified by the size because there are two prongs with the wires and two connecting prongs in the socket. I talked to a very helpful representative and she gave me the number for Frigidaire, when I was confused by the placement of the wire. Wish I had remembered her name to share with you. As it turned out I didn't need to call Frigidaire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Kiefer, OK
- Parts Used:
- 5303918774
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
broke fan blade while trying to remove dust.
Removed old fan motor and installed new one.Not much room for big hands back there.Flexible extensions valuable on this job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from vandergrift, PA
- Parts Used:
- 240524102
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
while cleaning the condenserI accidentally hit the fan blade and broke it
Had my 3 year old remove the 4 screws to holds the carboard in place. Pryde the old fan blade off with a screwdriver. slid the new fan blade on to the shaft then my 3 year old put the screws back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rusty from Howell, NJ
- Parts Used:
- 5303918774
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Fan would stop or turn slowly. outside of refridg hot
took off cardboard removed two screws holding fan housing. Removed new fan and housing from box and mounted new fan to new housing (two screws). Installed new fan and housing. reinstalled cardboard and plunged in power cord. Perfect fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Rockford, MI
- Parts Used:
- 5303918774
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Rattling Noise from behind frig
Initially, I traced the noise down to the evaporator motor area. I thought it was the fan blade so I ordered and changed it. Noise level better but still not good. Then I ivestigated problem area again. Removed the motor,discoverd that the motor shaft was loose /drifting which caused the "hummm" and uneven fan blade rotation. Orderd and installed new motor and all is good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from Stow, OH
- Parts Used:
- 241796405
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Ice Maker not getting any water
1). Shut off water supply to fridge. 2). Move fridge out to gain access to back of fridge. 3). Remove poly line to water tube have a glass handy to catch any remaining water that might be in line. Some may have a foam insulating washer around water tube remove it first. 4). My Sears-Kenmore was a twist lock water tube have to turn it to left or right depending on brand to remove tube. 5). After removing make sure tube didn't just have water frozen in tube ( that was my problem ) run it under hot water frozen piece will come out. 5). Problem fixed, reverse directions to re-install tube!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Akron, OH
- Parts Used:
- 241798231
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Ice maker quit working.
The two screws that held the ice maker in place could not be seen do to there location. I could only get one hand inside do to space restriction.So I placed a mirror inside so I could see the screw heads and from point it was very easy to see and line up the nut driver on the screw heads. I then lifted it up and unplugged the wiring and installed the new ice maker. Works like a charm. Paul
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from Jefferson, MD
- Parts Used:
- 215846604
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Freezer always has ice accumulating
Thermostat assembly, remove light bulb, remove 1 screw, drop thermostat casing, two screws to remove timer from inside and install in reverse. Old Timer had electric motor and lasted 30 years. New one looks to be electronic with plastic motor gears.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Salem, NH
- Parts Used:
- 241796405
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
leaking water onto the evap fan freezing causing alot of noise
1st a changed the defrost stat. Waist of time. Realized there was no evaporator above fan. Noticed ice was builing up behind ice maker near fill tube. Found if I shut off ice maker ice wasnt building up on fan. Moved fridge out unplugged fridge unscrewed plastic nut. Turned 90 degrees. Replaced tube locked in place . Screwed nut back on . Plugged in and turned ice maker on. Wife happy ice was back on and no noise.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from Benton, AR
- Parts Used:
- 240535101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
top door rack was broken at the connectors
The new part fit perfectly! I just snapped it on! Thanks so much Partselect! You processed my order quickly, and I had it in my hands in a few days. What a relief to have this fixed! Thanks again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Duane from Columbus, MS
- Parts Used:
- 240383801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing shelf.
Just snapped it on.
Was this instruction helpful to you?
Thank you for voting!