10672003018 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Karen from Ontario, NY
- Parts Used:
- WP67002633
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
didn't shut crisper pan and cracked pan with refrig door
replaced broked crisper pan with new pan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from LONG VALLEY, NJ
- Parts Used:
- W10830162
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Needed to replace gaskets in refrigerator door as they were cracking
Beware - the website does not indicate that doors are different sizes on this model refrigerator. Not paying attention I ordered 2 of the same size gasket which only fit the right side door - had to send one back and reorder left side from Whirpool directly.
The actual installation is very easy. It may take a day or so the gasket to feel like its actually making a good seal.
The actual installation is very easy. It may take a day or so the gasket to feel like its actually making a good seal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rich from Lansing, IL
- Parts Used:
- W10619951
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Freezer icing up .
Watched Partselect video of P-trap installation.Removed water line & back cover& disconnected wires to water solenoid .Removed old drain tube & old problematic rubber funnel. Used contact cleaner to clean rubber residue from drain line and used a little silicone to aide reassembly. Job went well thanks to video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phil from GREENFIELD, IN
- Parts Used:
- W11395888
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Remove the water filter to install the bypass cap
Lower the filter bottom housing to gain access to the filter. Unscrew the filter and install the bypass cap. Secure the lower filter housing to the top assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ethan from Fort Collins, CO
- Parts Used:
- W11291138
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Needed to replace a broken light switch
Popping out the broken switch was easy once I was able to see how the new switch part was engineered. The switch was made to be replaced, having a simple tension hook on the bottom of the switch which needed to be depressed to pull the switch out of the cabinet. Once pulled out, there were modular plugs for the power line that were easy to pull off the broken switch and plug into the new switch. Pop the new switch back in and VOILA, the lights worked again! Thanks to part select's good diagrams of the actual model of my refrigerator, it was very easy to hone in on the exact part I needed. I did notice one problem with the order as the correct series for the part was displayed earlier in the process, but had the wrong series later in the process. However,. I trusted the system and the part is for the right series and fit well (an exact match, down to the color). Thanks Part Select, I would definitely use you again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Long Valley, NJ
- Parts Used:
- EDR4RXD1
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Six months in use time to replace the filter
It is simple, unscrew the old screw in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martha from Janesville, WI
- Parts Used:
- WP67001716, WPW10671238
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Ladder hooks and center crisper rail broken
I removed the crisper drawers, glass shelf, and frame assembly to install the ladder hook. Before reinstalling the glass shelf on top of the crisper frame, I installed the center crisper rail.
Thank goodness for websites like this!
Thank goodness for websites like this!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from SPRINGFIELD, MO
- Parts Used:
- W10830162
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Right side door gasket split open
First, selecting the right part is more difficult than the repair. My Kenmore is an outdated model actually manufactured by Whirlpool.
Once I got the part I relaxed the gasket with a hair dryer - an important step suggested by PS. I then took old of the old gasket and removed it. The new one fits in the channel. Just press and make it is completely installed and flush.
Once I got the part I relaxed the gasket with a hair dryer - an important step suggested by PS. I then took old of the old gasket and removed it. The new one fits in the channel. Just press and make it is completely installed and flush.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sarah from Fayetteville, AR
- Parts Used:
- WP67006878
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I was cleaning the fridge and I broke the shelf into ten million pieces
Your service is wonderful! I found the part on my mobile phone with a very quick and simple search, then I called in to order. The ordering process took less than 3 minutes, and I had my new shelf in three days. I dreaded ordering, because I just knew that the replacement shelf would be super expensive, but the whole thing cost much less than I expected--less than a dinner out. Thank you so much for your efficient and friendly service!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Newton Grove, NC
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light switch rocker broke, disabling freezer internal light, water dispenser, and ice dispenser
Very simple. Matched female plugs with respective male color coded prong; pushed together then inserted unit in slot of freezer sidewall and rotated into position...job done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda from Spokane Valley, WA
- Parts Used:
- EDR4RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace water filter
pop open, unscrew quarter turn, screw new one in quarter turn, pop shut. duh
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aggie from Prospect Hts, IL
- Parts Used:
- WPW10671238
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Breaks relatevely often when you accidently have either draws overloaded or open both of them at the same time
You need to lift up the glass part and simply fit it the center rail in, very simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from West Warwick, RI
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken light switch
followed the instructions provided and that's it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Rocky River, OH
- Parts Used:
- WP627985
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
replacing thermostat did not help
Icecubes came out half-way, and refrooze. I figured out, that the melter does not work (HEATER in the icemaker) Voltage measured 105V no load. Studied the Internet, and folloved an advice: shorted the back wire and the blackwire with white stripes.these go to relay contacts. It seems, that the relay contacts are no good on Infrared receiver boaed. I turn off manually the icemaker, when needed
Was this instruction helpful to you?
Thank you for voting!