61004754 Kenmore Refrigerator - Instructions

Removed screws, removed parts, spring popped off, didn't know where it was actually at, had a difficult time getting the spring in the right place, (the directions were not that clear), put back together 6 times before I got it right.

The Refrigerator had panels of wood, they had to be removed above the Ice maker face plate before it could be lifted off. There were several layers of Torx screws to be taken off., had to purchase that tool. Luckily they were all T-15 and I guessed right at the hardware store. The rest of the repair went pretty as indicated on the sheet provided.

Shut off water and electric to refrig. Removed back panel. Removed water line. Removed valve, Disconnected other water line and electrical connections. Installed new valve in the reverse order.

removed the panel to get to icemaker(4 screws), then removed the plug, then removed worn solenoid and replaced with
new one. Had to jiggle old solenoid to get out,
but not with much effort. Everything went back
into place effortlessly

Just had to follow the easy to read instructions that came with the kit assembly. Only problem came when reinstalling the spring the recomended half a turn of tenison. seems like it was'nt enough tenison to completey close the door air tight. Would be much easier if the pictures where clearer and larger for older eyes to see.

Unplugged refrigerator. Removed 3 screws holding unit in place. Carefully disconnected the wire from the control face plate. removed existing ice dispense door and spring, disconnected lead from solenoid which controls ice dispenser door opening and closing. Removed 2 screws holding solenoid in place. Removed old solenoid and replaced with new one. Installed new ice dispenser door and spring. Replaced old actuator pad with new one and reassembled.
Repair was easy but unfortunately did not fix the problem. Subsequent tests indicate no power getting to the solenoid so I think I have a circuit board problem --

The video was fantastic provided by Part Select. Only difference I found was the use of shark bite connections, instead of screw on nuts for the top two hoses. Shark bites have to be pressed and removal can be done, would be a good idea for the video.

Followed the directions provided with the solenoid and door kit to replace solenoid, door and actuator. Replacing bracket was intuitive, just required transferring of parts from one to the other (miro-switch, cabling, light socket, and circuit board), and then installing the actuator pad on it.

Easy to follow directions. Got to the part where the old solenoid would be removed and found that one of the two wires the connected to the old solennoid had become disconnected. Reconnected and everything works. Will keep the kit now as backup and instructions in case I need to repair again. Very satisified.

This is an easy repair and doesn't take hardly any time, once you can identify the electrical bridals to disconnect and the position of the new ice chute door interface point with the solenoid.

The supplied directions are complete but were quite a bit blurry. The more general dissasembly which is effectively 5 screws and two electrical bridals to remove/disconnect is straight forward. Pay particular attention to the mounting point of the ice door interface with the solenoid. I did it twice because I didn't align the door properly the first time:-)

Much too easy a job than to "call the guy."

The repair was really simple - I followed the directions provided. I removed the screws holding the cover in place - unplugged the wiring harness - removed the solenoid and replaced with the new solenoid and door amd reassembled the parts. I wasn't sure if the solenoid was bad since the door was actually broken. I was able to test just using the new door - then replace the solenoid. It was all done in less than 30 minutes. Directions provided were GREAT.

First removed the grill from the fountain. Then removed the 2 screws, raised the escutcheon up and off the fountain assembly. Disconnected the power connection to the escutcheon and laid it aside. Removed the 3 screws holding the fountain assembly and disconnected the power supply from it. Removed the broken door pieces. Removed the 2 screws from the solenoid and replaced with new one and replaced the screws. The instructions said to rotate the spring counter clockwise 1/2 turn but I had to rotate it a full turn (to make the door tight when it closed) and insert the end of the spring in the opening of the fountain bracket. Insert the solenoid plunger into the recess of the door strike (the diagram in the instructions helped because this was the part that was broken and I could not figure out where it went). Then I installed everything back the way I had taken it apart.
I am a 61 year old woman and pretty good at taking things apart and putting it back together. My husband usually lets me fix things because I have more patience than him.
I would like to thank parts select for their packaging of the parts and the included diagram.

directions in package really made it easy. Saved $175.00

repaired by following the video instructions. the video is a great how to do it yourself tool !!!!

I just followed the directions that came with the part and it was very simple. Saved at least $100 on the repair. Anyone could do this repair. Don't call Maytag.