1068370511 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Raymond from Victorville, CA
- Parts Used:
- W11581579
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken bracket
Replaced broken shelf bracket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from Crete, IL
- Parts Used:
- W11581579
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Freezer shelf falling off
One of the front studs was broken off. I had to use pliers to pull it out (kind of tight). Then I inserted the back and front holders and layed the shelf back in. Total time...10 min
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- chris from woodland hills, CA
- Parts Used:
- WPW10662129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
you have to turn it off and on to run.
Just like the video showed me.It still does not work. Have to turn it off and on to make it start up.I also replaced thermostat in freezer. Does not work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from Centerville, OH
- Parts Used:
- 4318297
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the end cap broke
I had to use a screw driver to spread the prongs enough to fit into the area to secure it. Very easy. The service was great , we recieved the part in 2 days
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Suzanne from Plainville, MA
- Parts Used:
- 4318297
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
2 door shelf end caps were broken
replaice the end caps with new ones. very easy. happy with partselect.com
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lennon from Phoenix, AZ
- Parts Used:
- WP2196157
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Water Line To Ice Maker Broke
Looked up the process on you yube and watched the repair video from the parts website
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Columbus Junction, IA
- Parts Used:
- 4318297
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door shelf end cap was broken allowing items to fall out of refrigerator when opening the door.
Installation was a breeze! Simply place shelf front into end cap set and while door is supported with assistance from another person, press endcaps into slots of the door backing. A proper quick fix and no more items falling out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jamie from Sacramento, CA
- Parts Used:
- 4318297
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door shelf did not stay in place, the end cap on one side was broken
I simply attached the part. It was so easy. What amazed me is how easy it was to order the part. Locating the part was on line was the simplest item I've purchase, the diagrams of the refrigerator were very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from Dunmore, PA
- Parts Used:
- W11745278
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
replace hinge bracket on fridge door
taped the door shut ,measured a block of wood and stuck it under the door for support.....unbolted bottom hinge,slipped on hinge bracket and reassembled.no muss no fuss.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sanford from South Orange, NJ
- Parts Used:
- 4318297
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic inserts broken
A little firm pressure snapped the new parts in place in the door so that the shelf could be replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Morgan, UT
- Parts Used:
- 833697
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
noisey fan
yup
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Hilliard, OH
- Parts Used:
- 482731
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Evaporator motor squeal.
After finding an almost obsolete part( thanks PartSelect!) the installation was rather easy. Remove the back panel of the freezer and vent with a screwdriver and a nut driver. Disconnect the three wires, green, white and red.Remove motor from mounting and replace with new motor. I had to make a slight adjustment to the ground wire on the new motor that required adjusting the position of the contact-no big deal. The motor fit perfectly. Popped fan on and assembled. 20 minutes max.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Brooklyn, NY
- Parts Used:
- 4387478
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Protective cover for bulb had melted
I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent items in the fridge from being able to touch. Bad solution.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- martin from grafton, WI
- Parts Used:
- WP2149705
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
non functioning light switch in fridge
This repair was super easy. there are only 5 screws to remove to get at the defective switch. 3 in the housing where the light bulbs are and 2 in the front trim piece where the cooling adjustment dials are. I never did unplug the fridge ,but probably should have although nothing bad happened. I removed all 5 screws using a 1/4" socket ( a nutdriver would work well also). there is also a small dia rod that comes down from the coolness adj. wheel that when you re-assemble goes though the middle of the wheel. The switch has only 2 wires that clip on with the push on flat type connectors. Very simple. I removed the wires and then the switch can be removed( it is only held in by 2 squeezable side clips). I put the new switch in and connected the wires , checked to see that the lights went on and off. which they did. then just put the screws back in.....done. also I would like to say that when I ordered my switch it came super fast. I ordered it online at 11:00am on a tuesday and it was on my doorstep in wisconsin by 10:00 am the next day...Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas A from SAN DIEGO, CA
- Parts Used:
- WP2196157
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Water ran all over freezer froze many times. Hair dryer to melt, Desaster!
Watched your AMAZNG detailed Video first. Ordered part received in two days,WOW! Pulled refrig. from wall unscrewed two screws, loosened third screw on hose, pulled hose out cut below metal incert. Took new part from package placed in back of refrig. placed new metal incert in hose replaced hose in new fitting. Turned water back on, plugged in refrig. No leaks pushed back to wall waited for while...VOILA!! ice cubes no mess to report. THANKS FOR SUCH AN AMAZING WEB SITE and SERVICE. TOM
Was this instruction helpful to you?
Thank you for voting!