25344703000 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Teresa from SOUTHFIELD, MI
- Parts Used:
- 240350608
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broken glass on top of crispers
Since the glass was broken and gone I just had to slide the new glass on top of the crispers. This was not really a repair, just an exchange of new for the old.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVE from LOS RANCHOS, NM
- Parts Used:
- 5304518034
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Defrost Timer
The old defrost timer started making a screeching noise (probably bearings going out). The replacement part was a cinch to install. When I initially spoke to a PartsSelect person, they said the part number I gave them was not consistent with my old '94 Tappan Freezer. They were able to still find the proper replacement part number. The video that was on-line helpful also.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dianna from HALE, MO
- Parts Used:
- 240364787
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
My Crisper cover was cracked and broken.
I ordered the replacement part. Cleaned out the bottom of my refrigerator, popped in the new part, replaced the food and was siting in my recliner in under 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from SAN FRANCISCO, CA
- Parts Used:
- 240350608
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Accidentally broke the glass insert.
Simply slide the new glass insert in!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allan from North Miami, FL
- Parts Used:
- 240338001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken door shelf bin
Opened the box, snapped it in place. Took longer to just open the box! I carefully inspected the part and compared to the original. I could not tell them apart. The fit and finish is perfect. This is a very well made product. Easy to order, fast shipping, well packaged and very easy to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from Shelby Twp, MI
- Parts Used:
- 240338001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bin had broken.
Replacement was a snap! Literally! OK there were two snaps. One on each side.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leon from Upper Marlboro, MD
- Parts Used:
- 240338001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Shelf Held Together with Rubber Bands
Old shelf was removed and the new shelf clicked right into place, an exact match, perfect fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tunis from NOLANVILLE, TX
- Parts Used:
- 297216600
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Freezer wouldn't shut off and wouldn't reach cold enough temperature.
Removed existing part, tested it, found it to be defective. OrderEd a new one and replaced the existing one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Jacksonville, FL
- Parts Used:
- 297217900, 5303305677
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Copper lines leaking freon
Removed the inside evaporator coil to do inside solder job, use torch to heat solder joints on the outside drier in order to remove it and install new drier. Soldered Heat exchanger line to drier and 1/4” copper line to compressor. Wrapped with new insulation wrap. Pulled a vacuum on system and then charged with 4.4 ounces of 134a freon. Works like a champ again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from ST PETERSBURG, FL
- Parts Used:
- 240524102
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
fan blade broke
Received fan blade part took about 5 min to install and running great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marguerite from LONG BEACH, NY
- Parts Used:
- 240338001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
plastic part broken
placed new shelf on refrigerator door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CAROLYN from SAN ANTONIO, TX
- Parts Used:
- 240350608
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Crisper glass shelf installed
Just like the video , just pull out the crisper drawers and slide the new one in. I also made sue that I had a quilt on the floor in case I dropped the glass shelf. Also if you are not sure of the model number you can try calling the store where you bought the appliance at which I had to do. I bought it at Conns and they just needed the phone number I used when I bought it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from GRANBURY, TX
- Parts Used:
- 5304518034
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Freezer not cooling due to icing up of coil.
The timer in this older unit is clearly exposed at the back of the freezer underneath the freezer compartment. It is attached with two Phillips head screws. After the screws are removed, the timer can be unplugged and the new one plugged in. The new timer has an extra flange to allow it to be used on more than one model of freezer. In order to mount the timer in this unit, you have to remove the extra flange by carefully cutting it away from the timer body, in similar fashion to what's depicted in the online video. This will allow you to mount the new timer to the mounting plate using the two screws from the old timer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from STERLING, VA
- Parts Used:
- 5303918774
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Condenser motor burned out
I followed the instructions on your website, made it a simple as possible. Very tight work area sometimes fingers only, but a little patience works.
Saved at least $300. By not paying a repair person.
Saved at least $300. By not paying a repair person.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from PRAIRIEVILLE, LA
- Parts Used:
- 5304518034, 297216600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
No problems
It went exactly like your on line video. It took longer to defrost the freeze than it did to make the parts change out.
Was this instruction helpful to you?
Thank you for voting!