10650289010 Kenmore Refrigerator - Instructions

remove the front cover. everything else is a quick disconnect type of connection. Nothing to it! I would remove the cover and check these connections anytime the dispenser does not work. Look for broken or disconnected switches. This reapir took me a couple of minutes whereas the repair guy wanted almost 200 bucks to do this job. Parts ran around 30 with shipping.

New part slipped right into the studs and fit perfectly

Removed upper hinge cover and hinge, lifted door from lower hinge socket, removed lower cam from 'frig hinge, and replaced with new. I had a helper hold the 'frig door while I removed old upper cam, and replaced with new. Piece of cake and works like new! This must be a design problem..

Just replaced the broken one without using any tools.

Removed the screws that held the control breaket. Then I removed (2) micro switches, and for a cable tie, I slide the old control bracket out and installed the new one purchased from your store. 5 minutes worth of work. THAT IT!!! It was very, very, simple the repair

We took out the old filter and put in the new one. Ran out a few gallons of water then it was ready to use.

Remove the unit cover by unsnapping from the bottom. Remove the face plate on the switches. The ice door simply snaps off the closing mechanism. The problem I have is that the original door included a heat trace element (keeps the back of the door warm to limit condensation). The new part was simply a new seal. I clipped the leads to the het trace (turn off the fridge before you do that) and put in the new door. When the heat ids on in the house there is no problem with condensation but on warmer days its pretty bad. I cannot find a replacement part with the heating element and have contacted Whirpool. THey haven't responded as of yet.

removed the drive shaft (6 sided) with seals and replaced it. They last for about 5 years and have to be rotated (flipped over) to continue to use. The shaft metal is a little softer than the drive socket on the motor which, over time will cause the six-sided (12 inch) shaft to round the edges due to torque and pressure on the mixing shaft inside the ice bucket the the door of the freezer.

I called a repair man from a pretty large name to come out and take a look. He found out in about 10 minutes that it was a bad capacitor. The quote he gave me was $75 for the part and $175 labor. I tried my best not to laugh and tell him no thank you. He did have to charge me for him to show up, which was only $98.
So I used what he told(minus the "scrap it") and opened it back up. Although he had left wires everywhere and the broken pieces laying inside, I thought it was enough for me to order the part. PartSelect was very easy to navigate and ordering was a breeze. Took about 4 days to get the part and I ordered in the X-mas craze. Fixed it in about 15 minutes.

I just slid the new pan in , partselect has the correct part all the time , I repalced my ice maker once and it took 15 min no problem

I unplugged the refrigerator
Opened the freezer door
Opened the ice maker door so that I could easily get to the emitter and receiver
I used a phillips head screw driver to remove 3 screws from the emitter plate and 3 screws from the receiver plate
I unplugged the faulty circuit boards--this took some tugging
I firmly plugged in the new circuit boards and replaced the screws
I waited about 30 minutes and the ice maker began making ice again

After receiving the replacement emitter and receiver boards from PartSelect.com, I following the troubleshooting paperwork that came with my order to ensure the parts I ordered where the problem. After which, it was very straight forward: unplug the frig, unscrew the 3 screws on the covers for each board, unplug the push-pin connection, remove the board screw, set the new board in, and plug back into the connection. It took approximately 20min.

Ordered the parts from Parts Select and had them within two days (lightning fast shipment--and with just standard shipping). Disconnected the power to refrigerator, removed three screws from each cover panel, pulled the panels loose from the freezer wall, disconnected the wiring harness on each, removed the screws holding the two boards, replaced the boards with the new ones, attached boards to cover panel with screw, reconnected wiring harnesses, replaced the three screws on each side, restored power, and made ice! Whole job took about 15 minutes.

Remove old tray, replace with new tray.

Simple & easy.

Best part is I ordered on Monday & received on Tuesday!

First I removed all contents from inside refrigerator door.Then I removed (1) 10mil screw,which holds cover for top hinge.Next I removed the (3) hinge screws,and lifted door off of bottom hinge.Pulled off plastic closure cam from bottom metal hinge post.I cleaned metal post ,applied a small amount of vaseline to post, slid on new plastic cam,installed door, replaced screws.Very easy,10 to 15 min tops.