5967954901 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Alan from EASTON, PA
- Parts Used:
- W11396037
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
gasket had ripped over the years where they flexed when dooors were opened and closed.
last time i tried it right away after removing from shipping box.. relaxing with with hot air gun... was not to easy... this time i allowed gaskets to relax for a week on a flat surface. in a warm room.... took less than 5 minutes per door.... no hot air needed.... VERY easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Allentown, PA
- Parts Used:
- WPW10312696
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
not making ice
watched video
took me less than 5min. to replace inlet valve.
an cleaned my frig at the same time that took me longer to do.
took me less than 5min. to replace inlet valve.
an cleaned my frig at the same time that took me longer to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Illyssa from GREELEY, CO
- Parts Used:
- WPW10662129, WPW10194431
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Fridge and freezer were too warm
Chose these parts based on suggestion on this website, as well as other sites. They did not correct the problem. Shipping was also quite slow.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Blair, NE
- Parts Used:
- W10874836
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Broken plastic hinge holding bottom drawer lid.
Took the food out. A couple of screw removals. Put drawer lid on and then put the screws in. Nothing to it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Justin from KANSAS CITY, KS
- Parts Used:
- W10874836
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Socket set
The right end cap hinge broke for the pantry door.
I replaced both side. The left side I very easy to replace. It has 2 screws holding the end cap in place and the tracking has 2 screws holding it in. Undo the 4 screws and put the track on the new end cap and then you are good to go to install the new end cap on the left side. Now for the right side is easy, but you now have to also undo 2 screws and other 2 for the track just like left side but also you are going to have to undo the humidity control stuff and put it on the new end cap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from DRYDEN, MI
- Parts Used:
- W10874836
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
The small peg that holds the panry door in place broke, as a result the door would not operate
It took longer to empty the items off the shelf than it did to do the repair. Slid the veg, drawers out, set them aside.Took glass shelf out set it aside. removed three screws with 1/4in socket. Removed end cap. replaced with new end cap, replaced screws, cleaned and replaced shelf and drawers. Was a very easy task. these pegs break very easy, this is the second time I have had to replace the end cap, both times it was the left size. problem is you have to buy both the left and the right side together,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erik from Cumming, GA
- Parts Used:
- W10874836
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Hinge on 'goumet lid' in front broke off
Wasn't a big deal. Removed the the shelves and glass immediately above the endcap as well as the large 'goumet' draw. Used a nutdriver to remove two screws. Popped off the old endcap and did everything in reverse. Replaced the long clear goumet draw cover that was still intact. Thanks for making it easy!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from ALIQUIPPA, PA
- Parts Used:
- W11396037
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Gasket torn
Pulled old gasket off door put new one in channel on door pushed gasket in channel less than 10 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from WALLA WALLA, WA
- Parts Used:
- WPW10300024
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
original ice maker would make ice and then water would over flow into ice bin and freeze
stick the very small screw driver in the hole on the left side cover and lift up to release the keeper tab,pull out to expose the wire connecter.insert the small screw driver in the slot on the left side to release the tab while pulling apart the two connectors.tuck the wires tight to side and pull out the ice maker.I thought I was getting the whole ice maker assembly,but just got a part of it,so I had take it apart and put it back together.the hardest thing to change over was the stop lever arm that senses the level of ice in the bin.after all this,it didn't work at all.not happy around here.back to filling ice trays
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from LITCHFIELD, NH
- Parts Used:
- WPW10312696
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
No water from door, but icemaker working
I easily ordered the part. When it came in, I just shut off the water, disconnected the electricity, and followed instructions to remove shelving and drawers. Then removed the rear interior cover, removed the old water inlet valve and installed the new one. Just a couple moldex wire connections and the 3 water lines in and out. Don't know if this is still ok, but so simple a caveman could do it. Sorry Geico.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- chris from las vegas, NV
- Parts Used:
- W10874836
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
broken end cap
took out the drawers and glass shelf and unscrewed the sides took parts for drawer glide off put them on the new part reinstallled saved $110 service cll and $20 on the part!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angela from Topeka, KS
- Parts Used:
- WPW10534153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator was missing grille
This grille just snapped into place without the use of tools. Couldn't have been easier. And the delivery was super fast; I ordered online one day and the item arrived the very next day.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Hardin, MT
- Parts Used:
- WPW10642944
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I scratched the door handle while moving the refrigerator into my house.
With a small allen wrench, I was able to loosen the two screws to remove the door handle and replace the new on without any problems. A very simple operation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claude R. from Clarkesville, GA
- Parts Used:
- W10874836
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The lid tab on the Wide-N-Fresh lid was broken off
I ordered the part and it arrived in about 5 days. I removed the two lower crisper drawers and the glass shelf seperating these from the Wide-N-Fresh compartment, to give me room to work. I removed the two screws holding the right side endcap in place. The temperature adjustment mechanism was a bit tricky to remove from the broken endcap and replacing it on the new endcap. Once that was figured out everything fell into place and the lid was snapped into place and worked properly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steve from St. Louis, MO
- Parts Used:
- W10874836
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Broken tab that deli drawer pivots on.
Receive part in two days. Super fast.
Repair was very easy. Whirlpool designs so even the "average joe" can fix it. Took abour 20 minutes to repair. Even with no directions.
Repair was very easy. Whirlpool designs so even the "average joe" can fix it. Took abour 20 minutes to repair. Even with no directions.
Was this instruction helpful to you?
Thank you for voting!