25354669409 Kenmore Refrigerator - Instructions

Installation was completed by following the online Parts diagram. Had to completely remove all parts, including the blades in ice crusher, and re-assemble. Glad the online diagram was clear and easy to read.

Removed the Plastic Cover at the top of the door. (One Phillips Screw ) Removed the Hex Screws with socket set. Lifted EMPTIED door off bottom hinge. Pulled the broken bearing out with needle nose pliers. (Very Easy!!!) Placed new bearing into slot and reversed the procedure. 15 minutes tops. I spent more time cleaning the door and gaskets than replacing the parts. Funny thing, I called the local appliance parts store and they stated this is a common problem. However, for such a common problem, they didn't carry the part and it would have cost more than what I paid here. Additionally, I paid for 3-5 day delivery. Part was here in 2 days. Awesome!!!! I'll always come here first for all my parts needs. A+++

Ordered a new shelf which arrived very fast. Installed in no time at all as it just slides in and rests on brackets. No tools needed and the new part looks just like the original.

The old support just unscrewed & then the new one screwed right on with two screws.

loosen 2 screws
unplug connector
remove
replug
replace
tighten 2 screws
done

The parts supplied were made to fit. The hardest part was getting the original broken tabs out of the internal walls of the fridge with out damaging the internal insulation. I punched the center locking pin through completely, dug out the broken tabs and then reached into the hole with a dental pick and pulled out the center pin. The new parts fit perfectly and with a plastic mallet, tapped the new locking pin into place.

I removed the back cover and removed the clip holding the compressor- run capacitor and start relay. I replaced these 2 components and clean the dust from the frig., and from the bottom of the floor. I replaced the back cover ; Loss about $300 worth of meat when when the frig. failed. Then I thought that, during these turbulent times, there are many which don't have a refrigerator or any meat to place in it, The refrigerator is "running" normal again.

Pulling the old seal was the easy part. The problem became dificult when I opened the seal package. Either Part Select or UPS had folded the seal in half. Witch caused the wire inside the seal to become crimped up. I used a pair of pliers "carefully" to straighten the wire as best I could. Luckly it worked, after pressing it firmly all the way aroud about 5 or 6 times. I'll still keep an eye on it for the next couple of weeks.

It wasn't clear how to disassemble the Ice / Water dispensing unit to get at the lever for replacement BUT the website had a great exploded parts view of the door and assembly so I was able to print that and from the diagrams you can easily work out how to pull it apart..
A bit fiddly and you need to power down the Fridge as there's 120v behind this panel (tip : dont drag out a heavy fridge, flip the breaker at the main panel to isolate the power) .

All fixed for $50 , compared to having to call out some guy who'd charge me $100 plus parts !! great deal !
Thanks !

Turn of power at the circuit breaker.
Remove the water tray by pulling straight towards you.
Remove the three screws at the bottom of the control panel.
Have someone hold the control panel while you remove the six small screws that retain the circuit board.
Gently ease the circuit panel away from the plastic frame and disconnect the six wire connector on the left hand end, followed by the two light connectors with black & red wires, then remove the four wires with spade connectors from the microswitches - noting where each goes. The control panel & circuit board can then be set aside.
Remove the three screws that retain the interior plastic frame. The plastic frame can then be eased forward taking care not to pull out the water pipe. This allows access to the screws that hold the actuators, which should both be removed. Unhook the spring & remove the broken actuator. Feed the new actuator wire up from the bottom of the frame and insert the left hand pivot first and twist gently to snap the right hand pivot into its recess. Replace the retaining plates & screws. Don't forget to the hook the actuator spring into its clip. Test the operation and ease the plastic frame back into position and attach with the screws.
Re-connect and reassemble the circuit board and front panel in the reverse order.
Power on and enjoy a glass of fresh cold water! You may need to press the reset button on the front panel to reset the lights in the actuators.

The part was easy to find on the site, instructions were right on and it only took 25 minutes to accomplish with just a screw driver and a pair of pliers.

Took the ice storage bin out. Took the unit apart,and disamble the augar unit. Ordered parts from manufacture, which arrived in two days. As soon as I got the parts, I reassambled it. Work perfect. Good job!

put the new ones

First removed food from the refrigerator door.

Second removed plastic cover plate and metal plate assembly from top of door.

Third lifted door of metal pin on bottom.

Fourth removed broken closer plate and replaced
with new closer plate.

Set door back in place.

Re secured the metal plate and plastic cover plate.

Replaced the door shelves and food. DONE.

I had removed the housing that the drum was in and taken the screws out to get to the broken drum. I removed it there was a set of 6 blades that crushed the ice that had to go back on the same order when I removed these I put them on a piece of wire in the order they came off (so I would get them back I the correct order). Then I reversed the order and reassembled it in the opposite direction . It was fairly easy to do. I'm a 68 year old disabled woman so if I could do it I'm sure you could to. Good luck. It cost me $14.00 if I had bought the whole assembly it would have been $150.00. So it was well worth my time and effort.