59677533700 Kenmore Refrigerator - Instructions

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

I removed and replaced the suspect Control board. The problem with the select switch not responding still existed. I then ordered a new “PS2371545 Dispenser Front Overlay – Black”. This cured all but one of the non responsive select switch problems. I notified PartSelect that I received a defective board and they promptly sent a replacement Overlay. This cured my problem. Thank you for your Help with my problem. I highly recommend your company. Bill S.

Through out broken plastic, replace with new one
to be replaced in a few years.

Pushed the hinge pins aside and removed the old lid.. Reversed the process to install the new lid

I was about to waste $1000 on buying a Refrigerator. Took 1 mins to search on google "Refrigerator doesn't work". Found a video on youtube, showed a step and step video to solve my problem. Order the part $50 and it took me less then 5 mins to install it. =)

Removed all of the bottom drawers and shelvs, then removed the end panel that contained the broken Deli cover hinge pin. Replaced with new panel, cleaned all of the existing parts and ten re-assembled.

First I removed the drawers and shelf above the pantry drawer and then removed the pantry drawer. The end cap came off very simply by removing two screws. I removed the slide attachment to the old end cap and attached it two the new end cap. I then installed the new end cap and replaced the drawers and shelf. The lid to the chef pantry popped right in place. Job complete.

First I removed the relay and over load and exam. Saw that the relay was burnt. Before I order the part I check to see if the compressor was still working by jumping the common start and run terminals.It did. I also checked the start capacitor with a capacitor tester it was good. I than order the part which came the very next day.Installed the part

The end cap is a very easy job to remove. Removed the three screws that hold the end cap in place using a 1/4 drive socket. Removed sliding rail which is affix to end cap to be reused with new end cap. Installed new end cap with the three screws and your done very easy. What made the job possible was the ability to identify the part from the PartsSelect.com web site which has excellent parts identification catalog.

I pulled the whole unit(condenser&overload relay)
with my hand & disconnected the wire connected
to it & Replaced it with the new one.Peace of cake.

changed the starter connected to the compressor

Lifted out the glass shelf and then removed two screws to get the right side end cap off. This side has a mechanical slide to adjust the amount of cold air into the Deli area.

You will need to carefully remove the plastic slide linkage from it's guides so that you can turn it sideways and it will then come off the end cap.

If it wasn't for that minor slowdown it would be a five minute job.

Thanks to this web site for QUICKLY getting me the part and providing info on how to do the job.

The parts arrived VERY quickly.Replacement was extremely easy even though the right side end cap has the temperature adjustment it only took 15-20 minutes.

Refrigerator was stored for about 2 years and we picked it up when the owner decided to move into an apartment and no longer needed to unit (lost home to foreclosure). Brought the unit home and it worked great for about 3 days. On the third day my wife noticed a slight electrical burning smell. I did also and quickly emptied the unit and hoped for the best. The unit did indeed stop working. I fancy myself a do it myselfer but I would normally not go near electricity but thought what the heck it was free if i ruin it I would give it away. After a little research i found Partselect and they had a great design and a few stories that sounded similar so i pulled the relay capacitor for the compressor and sure enough the unit showed burn marks where the unit had shorted out. Maybe a bug got in there or water, dirt but I ordered the part. I arrived in two days which was great. I installed the part and plug the unit in and crossed my fingers. Very happily the unit clicked on and has been running great ever since. thanks Partselect, while I may not be one of your big customers I will refer anyone with appliance issues to your site first.

Snapped new cover on.