5967954201 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- ROBERT from Lufkin, TX
- Parts Used:
- W10874836
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Plastic hinge pin broken on original endcap
Really easy - Remove drawers, remove glass shelf and associated support rails, remove drawer slide from old endcap, remove old endcap, reverse proceedure installing new endcap - now the hard part, have a cool softdrink while you carry the old endcap and packing material from the new one out to the trash.
By the way - the part got here really fast - thanks for the great service.
By the way - the part got here really fast - thanks for the great service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from MARYLAND HTS, MO
- Parts Used:
- WPW10662129
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
freezer (later fridge too) wouldn't stay cold~
****Make are you order Capacitor & Starter relay too (we ordered separtely so had to pay shipping twice)**** Super easy just open access panel on back near compressor and remove retention clip with fingers, remove & replace both capacitor & starter, put clip and access panel back on, plug in and allow 8 hours to cool! Works like new again! Hope it goes another 10 years
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from MABLETON, GA
- Parts Used:
- W10619951
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Easy fix for Whirlpool refrigerator
I followed the video provided by Part Select. I also let the refrigerator stay unplugged overnight with all the doors open. This p-trap kit has fixed the leaks out of the front of the refrigerator. There is no ice build-up in the freezer. Perfect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claude R. from Clarkesville, GA
- Parts Used:
- W10874836
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The lid tab on the Wide-N-Fresh lid was broken off
I ordered the part and it arrived in about 5 days. I removed the two lower crisper drawers and the glass shelf seperating these from the Wide-N-Fresh compartment, to give me room to work. I removed the two screws holding the right side endcap in place. The temperature adjustment mechanism was a bit tricky to remove from the broken endcap and replacing it on the new endcap. Once that was figured out everything fell into place and the lid was snapped into place and worked properly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Pleasant Mount, PA
- Parts Used:
- WPW10194431
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
The refrigerator was clicking but not turning the compressor on long enough to work. So the freezer was thawing and freezing which froze the drain line completely. Forcing the water to flood the refrigerator.
I unplugged the capacitor which allowed access to the on/off relay. Unplugged the old broken one and plugged in the new one. All better.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steve from St. Louis, MO
- Parts Used:
- W10874836
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Broken tab that deli drawer pivots on.
Receive part in two days. Super fast.
Repair was very easy. Whirlpool designs so even the "average joe" can fix it. Took abour 20 minutes to repair. Even with no directions.
Repair was very easy. Whirlpool designs so even the "average joe" can fix it. Took abour 20 minutes to repair. Even with no directions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DOROTHY from WEST PAWLET, VT
- Parts Used:
- WPW10326469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The tab on the center drawer rail broke
Just emptied the glass shelf. Lifted it and installed new part. Easy Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jay from Parrish, FL
- Parts Used:
- WPW10326469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
A tab broke off a frame rail of the crisper drawer
replaced the part with a new part from partselect. No tools were required
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Colorado Springs, CO
- Parts Used:
- WPW10662129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
freezer and refrigerator compartments not cold enough
Used the suggested problem list here to narrow down that the repair was most likely the run capacitor. Poped the new one in and I now have better control of my compartment ranges. I have a temperature gauge in each compartment. Check them every opening of the doors.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from wenham, MA
- Parts Used:
- W10874836
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Pin on end cap broken
the only thing easier than installing the part was finding it on this website.
10 minutes max start to finish.
Removed the 2 fruit & veggie drawers & deli drawer and glass top. Nut driver to remove the side end cap. Remove and replace the rails onto the replacement part and reattach. Simple.
It had been broken for months and I just kept putting off calling a serviceman. Boy am I glad I found your site. I don't even want to think about what this may have cost. When the kids break something else I'll be ready !!
10 minutes max start to finish.
Removed the 2 fruit & veggie drawers & deli drawer and glass top. Nut driver to remove the side end cap. Remove and replace the rails onto the replacement part and reattach. Simple.
It had been broken for months and I just kept putting off calling a serviceman. Boy am I glad I found your site. I don't even want to think about what this may have cost. When the kids break something else I'll be ready !!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from WISC DELLS, WI
- Parts Used:
- W11033333
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No problem
Slid the new glass in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from MT PROSPECT, IL
- Parts Used:
- WPW10534153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Clip cracked on back of kickplate and would not attach.
Pushed on new one as directed online.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from FORD CITY, PA
- Parts Used:
- WPW10662129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Freezer occasionally had a temperature alarm.Clicking noise also.
Was told capacitor was problem 90% of the time.Capacior was not the problem.Bad start relay.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adam from GLOVERSVILLE, NY
- Parts Used:
- WPW10662129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Plugged it in.
Not so good that was not the problem. Fan is not seized and all the lights work and display is not on but lights up as well. No start once plugged back in after 15 minutes of being unplugged. Nothing same no change.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Altamonte Springs, FL
- Parts Used:
- W10874836
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The closure lid retainer tab had broken off of the pantry end cap
First I removed the two vegetable bins. I then removed the glas top shelf from the pantry and removed the pantry drawer. There were 3 screws that held the pantry end cap to the interior of the refrigerator. I removed the three screws. I then lifted up the front end of the end cap allowing it to snap free. I then snapped the new end cap in place and reinstalled the screws. The rest was just reversiing the drawer installations.
Was this instruction helpful to you?
Thank you for voting!