59678539802 Kenmore Refrigerator - Instructions

Took the shelf glass out, pulled drawer out, put lid on put shelf back together. Everything fit and works well.

I ordered the part and it arrived in about 5 days. I removed the two lower crisper drawers and the glass shelf seperating these from the Wide-N-Fresh compartment, to give me room to work. I removed the two screws holding the right side endcap in place. The temperature adjustment mechanism was a bit tricky to remove from the broken endcap and replacing it on the new endcap. Once that was figured out everything fell into place and the lid was snapped into place and worked properly

I followed the video provided by Part Select. I also let the refrigerator stay unplugged overnight with all the doors open. This p-trap kit has fixed the leaks out of the front of the refrigerator. There is no ice build-up in the freezer. Perfect!

****Make are you order Capacitor & Starter relay too (we ordered separtely so had to pay shipping twice)**** Super easy just open access panel on back near compressor and remove retention clip with fingers, remove & replace both capacitor & starter, put clip and access panel back on, plug in and allow 8 hours to cool! Works like new again! Hope it goes another 10 years

Receive part in two days. Super fast.
Repair was very easy. Whirlpool designs so even the "average joe" can fix it. Took abour 20 minutes to repair. Even with no directions.

this pantry lid was warped when the fridge was new. tolerated it for a while finally it cracked then worked pretty well for a couple years until the RH hinge pin (part of a support for the pantry door)broke. I had never bought parts from partselect.com before, but I have in the past bought repair parts from other sites. Partselect.com had drawings of the refrigerator parts that although were a little hard to see were adequate to tell what parts I should order. I ordered the parts, they came in after an acceptable wait. The parts were literally perfect, went right in, and everything is working quite nicely. I am happy with Partselect.com and will probbly go to them first in the future. I actually like the refrigerator a little more now than I did when it was new.

The installation video for condenser fan motor helped a lot to know how to disconnect the old fan motor and connect the new one. So easy just know how to remove and put back the fan gently, observe carefully where is the center and the connector position; 15 min after everything was done and the unit works well to date.

Removed cover ,two veggie bins, glass glass shelf, all took 10 min. It took longer to wipe clean every thing I installed the new end cap with 3 screws, I had to add one of my own as the factory only used 2 the rear one was not installed.it didn't matter.One thing that I didn't like was the parts came with no info, but my 40 years of working for air lines made the job easy for me.

Pretty simple, remove the pantry lid, drawers above glass pantry cover and then the glass cover and its metal supports.
Then the pantry tray from its metal slides.
Remove the slides then the broken end cap.
The slides and end caps are attached with 1/4 inch hex drive screws.
I did notice a small change in the new end caps which will improve the
strength of the problem tab. I do not expect the same problem again.

I removed the pantry door, the pantry drawer and the glass shelf above the pantry drawer. I removed 2 screws/bolts from the left side end cap and removed it. I simply installed the new pantry end cap with the 2 screws/bolts and tightened them snuggly. I then replaced the pantry drawer ...installed the glass shelf...reinstalled the pantry door and that was it...the wife took over after that

Removed the access panel on back of unit located the Run Capacitor on the compressor and removed the bad one and put the new one on and pugged refrigerator back in and it started up and works fine now

I ACTUALLY FOLLOWED A PREVIOUS BUYER'S INSTRUCTIONS WHICH WERE TO REMOVE THE CRISPER DRAWERS, THEN THE GLASS SHELF WHICH THEN ALLOWED YOU TO GET TO 3 SCREWS THAT HELD THE END CAP IN. FROM THAT I HAD TO REMOVE THE DRAWER SLIDER 2 MORE SCREWS. THEN DO JUST OPPOSITE TO PUT IT BACK TOGETHER. ALL SCREW HOLES LINED UP WITH NO PROBLEM. AND I AM AN 85 YEAR OLD WOMAN.

Removed the 3 bottom drawers and shelves. Removed 4 screws from the old parts. Removes the screws from the existing guide rails and transferred them to the new parts. Put everything back in , in reverse order. Just take your time and do not over tighten things.

Two screws hold each of the panels onto the refrigerator. Two more screws hold the metal drawer guides. Once the panel is released from the refrigerator, the metal drawer guides need to be transferred to the new panel. This step is repeated for the right side panel. The right side panel contains the air flow mechanism controlling how much cold air is released into the pantry drawer. It is attached by a network of plastic tabs which need to be pushed back in order to release the mechanism from the panel. A flat screwdriver is helpful to do this. I'm not positive that the air flow mechanism along the back of the refrigerator went back into place correctly; it seemed to sag a bit as it's not attached by screws.

Replaced left end cap-really easy. Have difficulty with humidity control on right endcap. Perhaps I can find some instruction on that.