59678339803 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Daniel from GEORGETOWN, TX
- Parts Used:
- WPW10534162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broke my original Kickplate Grille
knelt down, positioned replacement kickplate; popped into place, stood up!
took longer to open the box and peel bubble wrap off item than to replace it!
took longer to open the box and peel bubble wrap off item than to replace it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Monte from Longview, WA
- Parts Used:
- WPW10534162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I purchased a display model that was missing a part.
Snapped on the new toe grille.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from SMITHFIELD, RI
- Parts Used:
- WP12825803
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
I had a loose fitting old condensor fan blade on my new motor.
I made a temporary repair by drilling the old blade plastic hub and put a small screw in it to hold it on to the shaft until the new blade arrived. The new blade came in within the two days I needed before Thanksgiving. I removed the old and pushed on the new. There were 8 screws on the back guard and two to hold the motor on. It was a snap.
Thank you PartSelect.com The wife is very, very happy now, we had 51 coming over for Thanksgiving. :)
Thank you PartSelect.com The wife is very, very happy now, we had 51 coming over for Thanksgiving. :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joella from THE DALLES, OR
- Parts Used:
- WPW10671238
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The center rail was broken
The part just snapped in. super easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rodney B. from Crestview, FL
- Parts Used:
- W11395888
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Filter stopped up. Causing the refrigerator to make a loud noise. water dispenser didn't work. less than 4.00 fixed all that
Shut off water supply. filter is located in the upper right hand corner of the refrigerator on the inside. open the drop-down door. by hand pull the filter downward. then twist it to the left one quarter turn. it should pull out. I replaced it with a filter bypass plug. you can purchase a high quality filter to replace.it don't buy cheap filter.I made that mistake! hope this helps good luck!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Allentown, PA
- Parts Used:
- WPW10312696
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
not making ice
watched video
took me less than 5min. to replace inlet valve.
an cleaned my frig at the same time that took me longer to do.
took me less than 5min. to replace inlet valve.
an cleaned my frig at the same time that took me longer to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Fairview Heights, IL
- Parts Used:
- 8201515
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker wouldn't cycle
Originally I took the module off and found that a small plastic part had broken. Both pieces were still there, so I super glued them together and reassembled the unit. It worked great for a couple months. I realized it needed a more permanent fix, so I found the model # and looked up the part. That was very easy on your website. I ordered the part expecting it to take 4-7 days. It was at my house in two days! 15 minutes later I was makin' ice, and makin' my wife happy. Thank you for an all around great experience. I'll definitely buy from you again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Live Oak, FL
- Parts Used:
- WPW10671238
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rear mount tab broken on Center Crisper Rail
It took longer to empty the glass shelf above the Crisper Bins than to replace the rail. Since the part simply snaps in place, no tools were required
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Lexington, KY
- Parts Used:
- 8201515
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
The icemaker would not produce ice because the motor that pushed the cubes out had failed. The original icemaker failed in this way and we had the icemaker replaced by Sears Service for about $200. The second icemaker failed for the same reason after 18 months. I decided to do the repair myself t
Open the refirigerator door and push and hold the On/Off button at the top to turn off internal power. Open the freezer door and move the icemaker switch on the right side freezer wall to "off".
To get access to the icemaker, first remove a hinged plastic door that mounts to the ceiling of the freezer compartment by two hex screws. Remove the screws and the door so you can work with the icemaker without interference.
The icemaker assembly will slide out once the wireharness has been disconnected. To disconnet the wire harness, a while plastic shield has to be removed from the right side of the icemaker, just behind the water inlet.
Locate a hex screw on the bottom right rear of the icemaker and remove it with a socket wrench. Then the plastic cover can be pulled off.
Slide the icemaker out enough so you can get your fingers on the plug connector. It takes some effort to pull the plug connectors apart. Once unplugged the whole icemaker assembly can be removed.
The motor module is located on the left side and is protected by a white cover. This cover is not attached so it can be pulled off to reveal the motor module.
Remove 3 screws from the outside of the motor module and the module can be pulled out of the housing. Insert the new motor module. The module turns the shaft of the ice srapper arm. the shaft has a D shape which mates with the hole in the motor module so you may have to roatate the scrapper arm until the shaft shape matches up with the hole shape in the motor module.
Once the motor module is seated, replace the 3 screws and push the white cover back on.
Position the icemaker so you can reconnect the wireharness plug connectors. Once connected you can push the icemaker asembly back into the grooves of shelf rail. Reattach the while protector shield which covers up the wire harness plugs.
Open the refirigerator door and push and hold the power button to turn internal power back on. Move the icemaker switch on the right wall of the freezer to the "on" position and close the door.
The icemaker should start making ice within 2 hours.
To get access to the icemaker, first remove a hinged plastic door that mounts to the ceiling of the freezer compartment by two hex screws. Remove the screws and the door so you can work with the icemaker without interference.
The icemaker assembly will slide out once the wireharness has been disconnected. To disconnet the wire harness, a while plastic shield has to be removed from the right side of the icemaker, just behind the water inlet.
Locate a hex screw on the bottom right rear of the icemaker and remove it with a socket wrench. Then the plastic cover can be pulled off.
Slide the icemaker out enough so you can get your fingers on the plug connector. It takes some effort to pull the plug connectors apart. Once unplugged the whole icemaker assembly can be removed.
The motor module is located on the left side and is protected by a white cover. This cover is not attached so it can be pulled off to reveal the motor module.
Remove 3 screws from the outside of the motor module and the module can be pulled out of the housing. Insert the new motor module. The module turns the shaft of the ice srapper arm. the shaft has a D shape which mates with the hole in the motor module so you may have to roatate the scrapper arm until the shaft shape matches up with the hole shape in the motor module.
Once the motor module is seated, replace the 3 screws and push the white cover back on.
Position the icemaker so you can reconnect the wireharness plug connectors. Once connected you can push the icemaker asembly back into the grooves of shelf rail. Reattach the while protector shield which covers up the wire harness plugs.
Open the refirigerator door and push and hold the power button to turn internal power back on. Move the icemaker switch on the right wall of the freezer to the "on" position and close the door.
The icemaker should start making ice within 2 hours.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from COAL VALLEY, IL
- Parts Used:
- WP67006878
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
The old shelf shattered when we tried to clean it
Just slipped it in. I think it's a very poor design.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mario from EL PASO, TX
- Parts Used:
- WP67006331
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
the locking latch to the water filter cover had been broken for a while
Open the existing cover and carefully with the thumb and index fingers, pry the cover at over the left pin and remove the cover. Place the replacement onto the right pin and pry the left placing it over the left and you are done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from VINEYARD HVN, MA
- Parts Used:
- W10827914
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Drawer door broke
It snapped into place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dalton from BEAUFORT, NC
- Parts Used:
- W11197396
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
peg that swings the pantry door open and closed was broken off
watched partsselect video and simply followed the directions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from SAMMAMISH, WA
- Parts Used:
- WP12227303WD
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
My refrigerator vegetable bins were sagging when I placed veggies in it.
I came across this site and looked at the diagrams. Instead of buying a new crisper bin frame, I noticed that the crisper bin frame was missing the frame brace. I purchased the frame brace and installed it in the crisper frame, which was easy to push into the slot. This solved my problem. No more sag!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from MABLETON, GA
- Parts Used:
- W10619951
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Easy fix for Whirlpool refrigerator
I followed the video provided by Part Select. I also let the refrigerator stay unplugged overnight with all the doors open. This p-trap kit has fixed the leaks out of the front of the refrigerator. There is no ice build-up in the freezer. Perfect!
Was this instruction helpful to you?
Thank you for voting!