10658143802 Kenmore Refrigerator - Instructions

took old bin out replaced with new , two minute job
Parts select is an easy co. to do business with THANKS Andrea

Very simple, just remove two bolts holding the auger, One note: the auger comes with a new drive coupling sleeve so it is not necessary to order one.

replaced

Just put the new one in.

Part would not fit straight in. Used universal joint on end of extension to reach screw rather that disassemble front. Managed to slip the paddel just far enough to one side and angled to snap ice guid on and then slipped paddel back into place. Used a dab of candle stickum on the screw head to heep it in the socket and then inserted in door. $7 part, 15min and saved $$$$$$ over a service call;)

Have not installed yet as I'm on a quick TX-FL-TX turnaround. Bought and received the part in 24 hours...great. Order contained no instructions. I could probably figure it out myself just have not attempted yet.

Emptied draw of contents pulled draw out and inserted new drawer....easy pea-zee

I got model number off my unit and order the part. That was after trying a lot of different filters first. I did a rush order so I got it in 2 days. Pulled the unit out to shut the water off. Then took the back off so I could take the 2 screws that hold the water value . That way I wouldn't have to go back and forth. Now I went to the front. I already had had the vent cover at the bottom of the unit off. I had a head lap on so to make it easier to see under the unit. Then I use the nut driver or you can use 1/4 inch drive ratchet with sockets. To take the 2 screws out that hold the filter housing. Then lift the spring wire that is on the left side of the release botton. Then push the wire up out of the way. Reach back and pull the water value forward so you have slack in the water lines. Now you can pull the fliter housing out to you. Now release the 2 water lines by pushing down on the rings around the water lines and hold while you pull the water lines out. Now the old water filter housing is free you can set it to the side. I inspected the new filter housing for any deformities and cracks before I started installing. Now I hooked the water lines up by pushing them into the right size spring ring hole. Once lines was all the way in I pulled back on the water lines to make sure they were locked in place. Then I put a new water filter in and turned the water on to make sure of no leaks. Then I put everything back together in the reverse order I took it apart. Then I check the spicket to make sure everything was working right. After that I was able to push the refrigerator back in and then wipe everything up and I was done.

Googled with question about how to get to the repair as there were no screws on the faceplate. Found I had to lift the faceplate at the bottom and pry out. Was kind of hard to get the long spindle back through the ears of the bracket holder along with getting the spring of the door lined up for the spindle to pass through to the other side. Finally got it right and then just put it all back together. Frustrating at first but I had to get it done as my wife was tired of having to take large clumps of ice out of the ice tray..three years wait for the repair. That door being open let warm air in and let the ice melt just enough to stick together in a clump. All is well now. Longer you wait the more appreciative she is however. ha

Nothing to do, part came, fully assembled, it just went right into the door. Yea!!!

Ordered the replacement part, came in 2 days, opened the box,rinse and dried it and put in the door. Nothing to it.

Followed Door Removal instructions by removing the Top Screws from the Cabinet. Lifted Door OFF the Metal Hinge. Unscrewed both Lower and Upper Cams from the Hinge and Door. Replaced with new after coating with Vasoline. Lifted Door back in place with help from Wife. Only problem was guiding the Door back onto the Hinge. Works fine. Two year old Frig. This is a design problem, as the cams should last longer than 22 months.

Old part would not stay in place (broken). Recieved new part and snapped it in to place . No tools needed.

The troubleshooting time takes about 20 to 30 minutes. After checking out the solenoid (valve water), the water line, and the electronic board (emitter/receiver) are working fine. The only thing left is the ice module. I called Partselect and talked to a sale rep to make sure I get the right part, and the lady was so helpful by sendind the picture of the part so I can review before ordering it. I received the part in 3 days ( normal shipping) and did the folowings:
1) Unplugged the power cord from refrigerator.
2) Removed the ice module by removed a 1/4" screw from under the right side of the icemaker that retains the icemaker and a “U” plastic clamp and then pull out the whole unit it from the track.
3) Unplugged the cable connected to the ice maker.
4) Using the phillips screw driver to remove the 3 screws. Carefully pulled out the ice module and installed the new ice module.
5) Put the ice maker back to the freezer, plug the cable back to the ice maker and put the clamp and tighten the nut.
6) Plugged the power cable back to the wall.

The first ice I got in an hour and a full bucket of ice in less than 24 hours. I spent less than $80 for the whole thing. Thank you so much Partselect for the great service and the stories posted, it really helped me to get it done.

Built-in filter was corroded due to age. New filter corrected problem.