59677602803 Kenmore Refrigerator - Instructions

I just had to exchange the bucket, right part the first time.

Removed the three motor screws pulled off old motor put new motor in place replaced screws and re-installed. It was producing ice three hours later. I originally tried to obtian these parts directly from Whirlpool in which twice they shipped me the wrong parts. Finally gave up on them and entered the whilrpool part number which crossreferenced to new part number which was correct the first try. Thank you!

Removed drawers and glass top and support bars Two screws on slid bar two screws on end cap, Make sure you take time to remove air control it has two pivot points with small taps.
Then just replace parts as you had taken off very easy.

lift glass, slide new rail in replace glass. 2 min repair.

First I unplugged the unit, then I popped off the cover to the icemaker electronics. Removed 4 screws, pulled out the broken electronic panel, and replaced with the new one. Returned the screws and cover. The next moring the ice bin was full.

This must have saved me $300, and the inconvernience of waiting around for the repair man. He would have made two trips since he would never have had this part with him.

Removed the crisper drawers (pull out, then up & out), remove the glass shelf above the "pantry", remove the pantry door (easy because hinge stud was broken), then remove the pantry drawer. Use 1/4" nut driver to remove the broken LH End Cap...it pulls up and out. With the phillips screwdriver, remove/replace the steel rail for the drawer action to the new part. Replace in reverse order (after your neat freak SO cleans everything!).

(1) Removed the three screws which attached the ice maker to the freezing compartmnet wall in refrigerator; (2) Disconnected the power to the old ice maker; (3) Removed the old ice maker from the freezing compartment of the refrigerator; (4) Took the white front cover off of the old ice maker; (5) Disconnected the wiring harness from the old ice maker; (6) Removed the "ice making-stop arm" from the old ice maker; (7) Placed the items taken from old ice maker on to the new ice maker; (8) Reconnected the new ice maker to the power; (9) Placed the new ice maker in the proper position in freezing compartment of refrigerator and replaced the three screws. JOB DONE!

Lower the filter bottom housing to gain access to the filter. Unscrew the filter and install the bypass cap. Secure the lower filter housing to the top assembly.

Broken lid popped out, new lid popped in. No tools required. 30 seconds to replace. Great price, part shipped within an hour of placing my order and arrived the next day, although I only paid for standard shipping. Excellent service - will definitely order again if the opportunity arises!

Received the union I ordered, then discovered that the tubes were different sizes, so I had the wrong part. I had read elsewhere that it was necessary to trim the two ends of the tubes with a box cutter to stop the leaks - I did this, and the leaking stopped. I was then able to go to a local hardware store and get a 5/16 to 1/4 union and replace it. The leaking is stopped, and the water supply in the door is now working like new. No problem with partselect, but I did buy a caliper so that I can check tube diameters if I ever have a similar problem! This is a great site to find instructions - well worth the time to search!

Old gasket was pulled off with ease. New gasket came folded in-half in cardboard box and was flattened in several places. It was reshaped with ease with the heat from ny wife's hair dryer. Insrallatint took about 5 minutes and seal was perfect. Took less than 15 minutes total.

Easy repair. Unwrapped the new cover; pulled the old one off by releasing tabs. Inserted new piece.
Took less than 15 minutes. Looks like new. The replacement part arrived quickly from Part Select.

Contacted sears home service to perform repair. Quote for repair was $307. 43. ( $196. 90 For labor ,$102. 58 For part) plus $75. 00 For service call. Based on the charge, I refused the repair and ordered the appropriate part from "part select" (733947) (wpl 8201515) motor module for a cost of $81. 84. To my surprise, the part arrived the next day and in 15 minutes the icemaker was in a position to make ice, and has been producing ice ever since. To perform the module replacement, I had to remove one screw with a nutdriver, pull the icemaker out, disconnect a wire harness, replace the module and do the reverse procedure to complete the installation. I saved a total of $225. 59 By doing this repair myself. A lesson learned. . . . . I will always investigate doing a repair myself with the help from the people at part select. Very professional and they sent the correct part the first time.

Removed broken lid and snapped new one in place.

Not being a professional repair tech, I looked at this sites provided schematics of the ice-maker. I assumed due to the problem I had which parts to order. the parts arrived within 3 days and after I took the icemaker apart I quickly realized I ordered the wrong parts. I called and asked what to do. since I did not open the packaging for the "wrong" parts I was able to make a return. I then called back because I discoverd the part I really needed wasn't shown in the sketch. I was told that I needed to order a new motor and it would have the part I needed. I ordered the part and within 3 days it arrived. Once I had the new part I was able to quickly install. Now I have a icemaker that works better than new since ,now it does not seem to jam either.

To make the repair:
First remove the 1/4" nut head screw on the under side of the ice maker.
Remove the shroud covering the electrical connection.
Slide out the maker and depress the locking clip.
Disconect the electrical wires.
Pull off the motor cover (no screws).
Remove the three philips head screws from the motor housing. Gently remove the motor.
Next loosen the screws and pull the "black motor-mounting harness" untill enough clearance to remove the ejector arm and deflector tray. The new kit will have a new ejector arm and deflector tray.
Insallation is the reverse.
The schematics were very helpfull.
It was very simple and I saved a $150 service fee to have someone else do it for me.
PS. When I called I was able to speak to real live Americans who were able to help me, were pleasant, polite, and professional, AND they did not treat me like I was stupid because I am not a professional repair man. I will definately use this service again. and recommend to all my DIY friends!!