10662989301 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from RALEIGH, NC
- Parts Used:
- W10124096
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
Replacing Condenser Fan
I was anticipating that the fan would be facing the back of the refrigerator. It actually was perpendicular to the back. There was some difficulty removing the bolts of the fan. I persevered and was victorious.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from GALESBURG, IL
- Parts Used:
- 2159327
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
gasket sagging at the bottom and was not airtight.
I followed the instructions on the video you provided with my order. Removed the freezer door and used the putty knife to loosen the old gasket and installed the new one. I'm a 77 year old female and if I can do it, so can you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cathy from HOPATCONG, NJ
- Parts Used:
- W11384469
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light rocker switch broke and refrigerator light couldn't go on.
I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from BLACKLICK, OH
- Parts Used:
- W10124096
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
loud griding noise
stopped the fan and noise stopped ordered fan motor and fan with interface cable. Using 1/4 inch nut driver to remove screws from motor bracket installed new motor and runs like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- asberry from SAINT LOUIS, MO
- Parts Used:
- WPW10189703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
first a loud noise than noise stopped then the refridg. stop cooling like it should
after finding out what could be the problem I order my part which I got around 3 days unboxed it and replaced it in the freezer component which I had already dismantled made note how I took it off and replaced it in the same way took about 25 to 30 minutes quite easy for me was grateful for the solution and proud of myself after replacing it and it began to work now it's freezing and getting cold as it should Thank you my part store
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from LYNBROOK, NY
- Parts Used:
- 2159057
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Original door gasket split from age, no longer sealing snugly to refrig.
Inserted scraper behind gasket breaking it free from door, permitting a hand hold. While putting tension on gasket, slid scraper around door gently removing old gasket. Replaced gasket starting at top gradually working around door. No need to remove door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Xiaoping from KIRKLAND, WA
- Parts Used:
- W10854037
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no drawer
just insert
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bernard from DONALDSONVLLE, LA
- Parts Used:
- W11745278
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
door hinge broke.
Removed door and replaced bushing bracket was ok.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Justin from BROOKLYN, NY
- Parts Used:
- W10920279
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Fridge won't start
When you plug in the fridge it will begin to make noise, but never get cool. When you open the door it will stop and will not turn back on.
This part is listed as one that can fix the problem, but the installation video does not match my fridge.
I've replaced the capacitor (PS11757023), the compressor start relay (PS11740412), and condenser fan (PS1957416) and none of them have fixed the problem.
I really don't want to throw this fridge out. Please help! justin@jplt.com
This part is listed as one that can fix the problem, but the installation video does not match my fridge.
I've replaced the capacitor (PS11757023), the compressor start relay (PS11740412), and condenser fan (PS1957416) and none of them have fixed the problem.
I really don't want to throw this fridge out. Please help! justin@jplt.com
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from MEDIA, PA
- Parts Used:
- WPW10189703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
refrigerator was not cooling
Swapped out evaporator fan motor, solved the problem!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from BATON ROUGE, LA
- Parts Used:
- 2159057
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Gasket had several tears in it at the corners and was leaking air into the fresh food compartment
Removed the old gasket and ran the hard edged lip into the opening behind the door liner. Concerned that the gasket does not seem to be attaching itself to the door well. First put it on the side of the refigerator and it would not adhere enough to support itself. While it closes it just doesn't seem to attach with the magnets in the gasket. These magnetic strips have a weak magnet side and a strong magnet side. I wonder if they put the wrong side facing the door when they assembled it. Counter this with a new gasket for an upright freezer which was twice the length and attached itself firmly to the side wall of the freezer and did not slide down.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- guadalupe from RIALTO, CA
- Parts Used:
- W10124096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Motor sounded like a small little airplane under my fridge, very loud.
Unplugged the fridge first then took the bottom panel off with a 1/4 inch nut driver. Disconnected the wiring & used my ratchet to reach the 3 screws that held the motor. Took me longer to clean the bottom of the fridge then the installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from BULLHEAD CITY, AZ
- Parts Used:
- W10124096
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Noisy condenser fan
I suggest following video supplied with order confirmation perfect fit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bonnie E from MODESTO, CA
- Parts Used:
- WP4387503
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Freezer was working but fridge was barely cooling. Look further into how to test thermostat.
I just replaced my defrost thermostat after using the place-in-ice-water method, and I think it may not have been necessary. My timeline: my fridge was not getting cold enough. I realized it the day before going on a trip. I vacuumed the (very dusty) coils at the bottom, and the next morning the fridge seemed colder, but I thought I should order parts just in case. I ordered a heater and a thermostat. The fridge seemed to be operating normally when I returned from my trip, but I had the parts, so I thought I'd go ahead and dismantle the freezer and test the existing parts. My intention was to return both parts if the old ones passed the tests. I opened up the back of the freezer and there was no ice on the fins. I thought, great, the existing heater works! I cut out the thermostat, placed it in ice water, and didn't get continuity. So I decided to go ahead and put in the new thermostat. Because I'm not experienced with using a multimeter, I thought I'd test the new thermostat to see how the test should work. To my surprise, the new thermostat also failed the test! Stumped, I thought I might as well install the new thermostat, since I had opened the package and couldn't return it.
Further internet research suggests the place-in-ice-water method of testing is not adequate. One YouTube video by Parts Dr says to place the part in a working freezer. I froze my old thermostat and tested it; still no continuity. This thermostat may not be typical, though. The video discussed the temperature ratings on thermostats. The temperature rating on both (old and new) thermostats is L8.9-16.7C. That converts to 48-63 degrees fahrenheit, which obviously are not freezing temperatures. I'm not convinced I needed a new thermostat, but I trusted the videos I consulted earlier.
I cleaned the fridge thoroughly, so at least now I have a nice clean fridge to show for my efforts.
Further internet research suggests the place-in-ice-water method of testing is not adequate. One YouTube video by Parts Dr says to place the part in a working freezer. I froze my old thermostat and tested it; still no continuity. This thermostat may not be typical, though. The video discussed the temperature ratings on thermostats. The temperature rating on both (old and new) thermostats is L8.9-16.7C. That converts to 48-63 degrees fahrenheit, which obviously are not freezing temperatures. I'm not convinced I needed a new thermostat, but I trusted the videos I consulted earlier.
I cleaned the fridge thoroughly, so at least now I have a nice clean fridge to show for my efforts.
Was this instruction helpful to you?
Thank you for voting!