10662989301 Kenmore Refrigerator - Instructions

I have a grandson that works for Pantex. He replaced the fan and motor in less than ten minutes using only the nutdriver tool. My cost compared to local supplier and labor was about 75% less.

First let me say that the instructional video on your website for this repair was very informative. My son and I watched that before we began the repair. We unplugged the unit first. After removing the back cover, he unplugged the old fan's electrical connection, and then proceeded to remove the fan and bracket from the unit. We then removed the old fan from the bracket, installed the new one and then he reinstalled the new fan and bracket back into the unit. He used the included electric adaptor cable to complete the electrical connection, plugged in the refrigerator briefly to confirm all was well (it was), then replaced the back cover and we were done.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

New part was similar, except contact blade was for a full 1/4", my model utilizes 1/8". So I cut the blade in half with a hacksaw, filed off the rough edges and reassemblied the connector; attached it to the compressor
Now being a retired electronic engineer; who's great idea was it to hide a klixon inside the connector?

****Make are you order Capacitor & Starter relay too (we ordered separtely so had to pay shipping twice)**** Super easy just open access panel on back near compressor and remove retention clip with fingers, remove & replace both capacitor & starter, put clip and access panel back on, plug in and allow 8 hours to cool! Works like new again! Hope it goes another 10 years

Took out the old, cracked, crisper unit and removed the white trim piece on the handle so that we could re-use it on the new crisper unit (which, in spite of the $90+ price tag did not come with new trim). The whole thing took 3 minutes to do.

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks

PartsSelect diagrams at their website made it easy to find and order the right part at a reasonable price. I removed the lower glass shelf and frame that supports it. I removed broken track and slipped in the new track and snapped it in place with the orifice at the rear of the track over small peg in the back of the frame. If I had called a regular refrigerator repair man, i'll bet this job would have cost me at least 70 or 80 dollars,

I just slipped the new drawer into place. So easy, even a woman can do it! ( I am female!)

The bent hinge caused a bad seal which let in air into the freezer, so there was a ton of frost build up. I ordered the parts, and they came in 2 days! I figured what tools I needed, got my wife to help hold things, and in 20 minutes it was like new.

I first replaced the switch and had no results, I then ordered the Light Socket Kit, and because I had the experience of removing the panel to replace the switch, it took a few minutes to remove the two screws behind the panel, removing the temperature control knobs and then releasing the face plate which is secured by tabs at the bottom. The kit came with extra connectors in case they were needed, but they were not in my case and so I pulled off the wires, pushed the old socket out and the new one in. Attaching the wires to the correct pins, I screwed in the light bulb to be sure that the fix was correct and determining that, I replaced the screws that held the panel in place. Voila, I'm a happy camper who found some outdated jars in the back corners of the newly lighted shelves.

The first part I changed was the defrost timer but it did
not solve the problem, I replaced the bi-metal defrost sensor
and I have the same problem.

I can defrost by turning the clock manually and heater works.



























problem.

Order the part and just slide the pan in.

Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.

Got on floor, pulled broken parts off front of refrigerator. Clipped in new grille. Looks great!