25331428101 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Larry from Newton, KS
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Refer iced up and would not keep the bottom cool. It was 70 Farenheit inside.
I simply removed 4 screws holding the casing and then 2 more holding the timer. It was very easy. I then replaced the timer by unplugging and plugged the new one in. I replaced all the screws and the job was done. Less than 30 minutes. I was very impressed with the shipping time. When I ordered the part, I had it the next day.
Was this instruction helpful to you?
Thank you for voting!
broken end cap in frigde and freezer
I slid off old caps, then slid on new caps. I pushed down metal holding clamps and I was finished. The whole process was about 5 minutes. The parts select web site was great. I looked up my parts on the easy to use catalog and ordered them. Make sure you save the broken parts or write down the part numbers to make finding your exact parts easier. I wish all parts web sites were as easy to use as parts select.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from VENICE, FL
- Parts Used:
- 5303918202
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Refrigerator evaporator coil was icing up
The evaporator coil is behind the freezer. Remove the rack that makes the shelf and remove two 1/4” hex head screws I the back of the freezer to access the coil.
I used a hair dryer to melt the ice off the coil.
The thermostat clips on the refrigeration pipe to the coil. Remove the old thermostat and cut the wires at least a few inches from the thermostat. Clip the new thermostat on the pipe and strip about a 1/4” of the wire ends. The electrical connectors (provided with the new part) must be crimped to connect the wires.
I used a hair dryer to melt the ice off the coil.
The thermostat clips on the refrigeration pipe to the coil. Remove the old thermostat and cut the wires at least a few inches from the thermostat. Clip the new thermostat on the pipe and strip about a 1/4” of the wire ends. The electrical connectors (provided with the new part) must be crimped to connect the wires.
Was this instruction helpful to you?
Thank you for voting!
Broken Shelves on the door
Ordered the right parts thanks to your list of part numbers and where they were located on the refrigerator. They fit perfect and problem fixed in five minutes. This is the best site I have ever used!
Please keep up the good service you provide.
Please keep up the good service you provide.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Eatonville, WA
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Defroster didn't work
Ordered a new defroster timer and replace old one. It works just fine. A $35 repair vs a $500 new appliance.
Cool.
GWE
Cool.
GWE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from Penryn, CA
- Parts Used:
- 240505801
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light switch prevented door from closing.
The switch prevented the door from closing about 5 years ago. So I just taped the switch down, and lived without a fridge light for the last 5 years. Painful! And wasteful (food spoiled because we couldn't see it.) Thought I was out of luck, assuming light switches were all the same, got fed up again, and pulled out old switch,,and searched the net for the part number, and just started calling the manufacturer. I got this website after no luck in calling, and took the step to order...and in no time, got it replaced, and we cam see now! It feels like we got a new fridge!
Was this instruction helpful to you?
Thank you for voting!
Missing shelf retainer (just moved in)
I had to cut the retainer bar to length and then snap the end caps onto the bar. Then just snap the assembly onto the freezer. No problem!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Landover, MD
- Parts Used:
- 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bilb went out
replaced it
Was this instruction helpful to you?
Thank you for voting!
The Refrigerator Door Shelf Retainer bars were broken
I looked at the model number and ordered it through the part select. The delivery was real fast and convenient. Overal we had a very good experience with "Part Select"
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LEVI from SUTHERLIN, OR
- Parts Used:
- 240331401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing Door Shelf Retainer Bar.
Just snaps into notches on each side. Bar arrived bent from shipping. Replacement was overnighted at no extra charge. Great service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Roseville, CA
- Parts Used:
- 240311501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door brace was cracked
Just popped the new piece into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from East Granby, CT
- Parts Used:
- 240311501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
End of bracket was broken. Replacement part was perfect.
Simply clipped it on.
Was this instruction helpful to you?
Thank you for voting!
They Were Missing
Not much placed the 2 ends on the straight bar & put it in place on the refridgerator door dom russo
Was this instruction helpful to you?
Thank you for voting!