36358097891 Kenmore Refrigerator - Instructions

There are Great videos on YouTube!!! Turned off power,Removed trim ring, Pushed a philips head screwdriver in one of the holes underneath the electrical panel with the selector push buttons. This releases the electrical panel. There are Three wire sets with plugs. I removed the plugs and took the electrical panel out. Removed four Phillips head screws and pulled out the big paddle switch. This then exposes the flapper. Replaced flapper with new one and reassembled everything. When I had everything apart, I cleaned with window cleaner. It was pretty moldy from the water leaking. Turned power back on and tested everything to make sure I didn't mess anything up. Works great

Remove the one screw holding the unit in place, unplug it, slide in the replacement, plug and screw it in.

Replaced dispenser door flapper by following the do it yourself video in this site. It was really easy. Just be careful when removing the dispenser black bezel. I broke one of the little tabs when taking it off.

Easy. First, unplug the fridge.

1)Shut off then disconnect water line.

2)Remove water valve mount screw.

3)Disconnect electrical plugs and snip water lines (square cut lines for new valve).

4)Simply insert and seat water lines into their respective places on the new valve. Using adapters as needed, reconnect electrical plugs.

5)Mount valve and reconnect water line.

6)Turn on water supply and check for leaks. Possible leaks: water line or not fully seated lines to the new valve.

7)Restore power and enjoy :o)

I didn’t do the repair because I ordered two grommets. When they arrived, one of the packages was empty! Instead of just sending me another one, they refunded the part so I still need one. By the way, I was not refunded half the shipping either which was more than the part itself.

I Took the six screws off the back panel to get to underneath the refridgerator. took the 2 screws out of the bracket thast holds on the water valve took the 2 lines off and then put everything back

Had to defrost the freezer to melt off all the ice before servicing. Once that was done the icemaker replacement only took about 15-30 minutes to complete. The new icemaker came with many accessories and adaptors that were not needed and the instructions were based on replacing an older model and not really clear for my model. They mentioned not being able to use the new stripper but it was exactly the same as the old one so I left the new one in place. All in all it was easy and did the job.

Use small putty knife to cut internal sealant on ice maker door trim piece. Then you can easily remove it.

Replaced flapper. Followed the video. The lamp caused the removable plastic bracket (which supports the control panel and the ice chute) to fuse with the plastic frame in the door. Eventually broke the fused plastic, removed the bracket, and filed the rough broken plastic before reassembly.

I aligned the back of the controller with the slot in the icebox and it popped right back on. No more frozen vegetables.

Remove front cover did not remove wires remove ice and water unit took off flapper put new one on 5 minutes back together

Researched on internet/you tube; ordered part, and did the repair. Easy to do and saved the cost of a service call.

removed the bulb from the package unscrewed the old bulb & screwed in the new bulb.

Disconnected the power and then the water line. Removed the cardboard shield on back of the refrig. Then removed the faulty solenoid which was held in place by one bolt. Removed the two plastic water hoses and two sets of electrical connectors. I then reversed the process to install the new solenoid. I encountered two challenges. The new solenoid had a plastic housing that had to be removed and one set of the electrical connectors required an extension. The extensions were included with the solenoid, but there were no instructions.

Used the parts diagram from PartSelect.com to locate the valve. Removed the old valve and disconnected inlet water line and the 2 outlet water lines(one for ice maker & one for water dispencer). Reconnected water lines to new valve and positioned it back in place on the refrigerator. Problem solved -no more drip, drip, drip.