25354679300 Kenmore Refrigerator - Instructions

I recieved the part within 48 hours. I snapped the part in place and I was done in seconds.

removed ice maker box and disassembled crusher unit on front of box and installed new housing.

Replaced an evaporator motor which had previouly been put in to replace original with an alternative which changed the original electrical connectors. Had to replace those replacements witn originals which extended the changeover.
Now works like the original and very quiet because your motor fit in the original rubber bushings. The alternative motor was put in by the Frigidaire repair man and at considerable expense because the warrenty date had been exceeded by one month.

Followed instructions from others on the blog. Shut off water and electricity to the refrigerator. Removed the cardboard plate. Removed the old water valve. Cut the compression valves off and inserted the tubes into the new water valve. Attached the water valve bracket to the fridge. Tightened copper water supply.Turned on the water - no leaks. Plugged the fridge in. Tried the water and ice in the door. No leaks - everything worked perfectly. THANK YOU PARTS SELECT!

removed rear cover, removed screws, diconnected water line connections, cut off old water line connection, installed new compression water line connection, replace screws in water line housing, replace rear cover.

worked fine

unplugged the refrigerator after pulling it away from the wall. Removed the water tray fairly easily. I read from other experiences about the water tube, i was prepared. I clamp a surgical clamp to the tube before removing the dispenser module. Look at the water dispenser you will see a white tube protruding, clamp it to prevent it from backing out. I removed three screws and the ice/water dispenser removal was a cinch. Two screws were removed and the actuator snapped out and new one installed. Be careful of the panel power strip, if it comes out it can be easily reinserted. Just make sure you get it in correctly. The fitting holding the strip will slide down slightly , enough to insert the power strip and push it back in. 30-45 mins only snag was not paying attention to the orientation of the power strip. If I had removed it at first would have made the job simplier. in other words i installed the strip backwards and when powering up had no display, removed panel reversed the strip and all is well.
Even with this mishap, 30-45 min was consumed. Have fun DIYER's

very easy to install...shipping was really fast...i would order to this website again....

Installation was completed by following the online Parts diagram. Had to completely remove all parts, including the blades in ice crusher, and re-assemble. Glad the online diagram was clear and easy to read.

The replacement glass was a perfect match !!! So pleased...
I was very surprised on how quickly I received my part. I
would definitely recommend your Company to my family and friends. Thank you

I removed the screws that held the the ice dispencer from the bin. I than removed three screws from the bottom of the bin. I put the new plastic piece on the end of the spiral piece that
pushes the ice. I inserted the spiral piece back into the hole. I than screwed the ice dispencer
to the bin and re-inserted it back in the refrigerator.
It took me about 5 to 10 minutes. It's really easy!

The parts supplied were made to fit. The hardest part was getting the original broken tabs out of the internal walls of the fridge with out damaging the internal insulation. I punched the center locking pin through completely, dug out the broken tabs and then reached into the hole with a dental pick and pulled out the center pin. The new parts fit perfectly and with a plastic mallet, tapped the new locking pin into place.

Pulling the old seal was the easy part. The problem became dificult when I opened the seal package. Either Part Select or UPS had folded the seal in half. Witch caused the wire inside the seal to become crimped up. I used a pair of pliers "carefully" to straighten the wire as best I could. Luckly it worked, after pressing it firmly all the way aroud about 5 or 6 times. I'll still keep an eye on it for the next couple of weeks.

Remove the screws that hold the old valve to the side of the refrigerator. Next, detach each plastic tube and attach that tube to the same place on the new valve, and repeat (there are many valves). Afterward, I realized that many of the plastic tubes had become brittle and had mineral deposits, so I bought additional tubing for ice makers and replaced each tube, one at a time.

Ordered a new shelf which arrived very fast. Installed in no time at all as it just slides in and rests on brackets. No tools needed and the new part looks just like the original.

The old support just unscrewed & then the new one screwed right on with two screws.