25331619100 Kenmore Refrigerator - Instructions

Remove the cardboard access cover at the bottom back of the fridge. On the left side, locate the run capacitor. Remove it by prying it loose from its socket, after first removing the wire hold down clamp. One wonders why the clamp is there, which makes it difficult to get the run capacitor out. Be careful not to disrupt in any way the copper refrigerant tubes. If you mess them up, you will have wasted your time and effort trying to repair the machine. I was lucky, since a failed run capacitor is the problem only about 12% of the time, based on what I’ve read. Hallelujah! It was the problem with my fridge.

Just had to pop the old pieces out, assemble the new ones, and pop them in. Very easy. Anyone can do it.

Looked up similar problems and found it to be the defrost timer. All I had to do was remove the plastic portion in the fridge section to get to the old timer. Popped the new one in and put it back together. Works great now. Would have been almost $150 to have a repair company come out and fix it.

The refrigerator that came with the purchase of my house had a missing retainer bar in bottom shelf of fridge and a duct-taped retainer bar in freezer. When parts came, all I had to do after removing the duct-tape, was slide up the broken end cap to pop it off then, snap the retainer bars into the end caps and slide them down into place. No tools necessary. Should have done this two years ago when I bought the house!

Removed four screws for cover on refrigerator temperature controls, unpluged old timer and pluged in new timer. Replaced cover and screws.

I watched brief video on your website.

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

Unplug, remove 2 screws off back panel inside the freezer. Cut wires on old one and crimped in new one. Light to melt the shrink wrap that came with it. Pretty easy.

1.unpack box.
2. slide out of plastic bag.
3. open refirgheratior door.
4. slide in shelves.
5. fill with stuff.
6.figure out a way to reuse packing.

First removed existing damaged shelf retainer bar and end caps from freezer door. Next cut down new oversized retainer bar to size with hack saw. Then slightly opened up doubled over metal at each end of retainer bar with pliers and screw driver in order to create the small "nicks" that are needed to house the "bumps" that secure the retainer bar to end caps. Used tin snips for this. Next inserted new end caps and used pliers to crimp secure. Clipped in new assembly in freezer door.

Assembled the bar and ends, then slide into slots on door. Cross bars have tabs to lock in place. These tabs may need a little effort to get started.

I removed the housing at the top of the refrigerator compartment that contained the reefer light and temperature adjustment knob. This required a small nut-driver. Inside, I found the old defrost control, unplugged it, unscrewed it with a Phillips screwdriver, and replaced it with the replacement part. Then I replaced the housing to its original position.

Removed the housing with the light, 4 hexhead screws. This exposed the defrost timer, removed 2 hexhead screws, electrical connector and reassembled the unit.

Great resource and service, thank you.

First I removed the plastic grill (pulled out, no screws) from bottom of refrigerator, then I removed electrical plug & two screws from old timer (timer located on the front inside left lower side of refrigerator). Installed in reverse order.

I watched the video on how to change the defrost thermostat. I removed the back cover inside the freezer then I pulled off the old defrost thermostat and then using a pair of wire cutters I cut it off and then bared a little of both of the wires and then slid the heat sherink and wire connectors on the existing wires and then slid the other ends of the wires into the wire connectors then crimped the ends of the connectors and then tried using heat on the heat shrinks but still used rubber electric tape over it. I clipped the new thermostat were the old one was and then reattached the freezer wall cover and plugged the refrigerator back in. 24 hours later I checked the temperature in the refrigerator and freezer and both are running a lot colder.