1068490260 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from INNSBROOK, MO
- Parts Used:
- 4386774
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
One of the front wheels was broken in half.
Very easy. Left the front of the refrigerator so it is approx. 4 inches of the floor. (used a two by four. Removed the screws (one for each roller). Removed the rollers and replaced with new rollers. Reinstalled the screws with secures the rollers to the refrigerator. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Jay, ME
- Parts Used:
- 4387535
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
compressor clicks on for about 5 seconds and then shuts off, evaporator fan is running but no cooling in the fridge.
Disconnect power. Remove back panel on the refrigerator. Relay and overload is a modular unit attached to the compressor. Disconnect module from compressor, install new unit. While you're in there clean the condenser coils with a vacuum and clean the fan and condensate pan. Reassemble, and you're chillin. Total time approx. 15 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from FORD CITY, PA
- Parts Used:
- WPW10662129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Freezer occasionally had a temperature alarm.Clicking noise also.
Was told capacitor was problem 90% of the time.Capacior was not the problem.Bad start relay.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacqueline from LEXINGTON PK, MD
- Parts Used:
- WPW10662129
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
No cold
Like you video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adam from GLOVERSVILLE, NY
- Parts Used:
- WPW10662129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Plugged it in.
Not so good that was not the problem. Fan is not seized and all the lights work and display is not on but lights up as well. No start once plugged back in after 15 minutes of being unplugged. Nothing same no change.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from COVINGTON, LA
- Parts Used:
- 833697
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
refrigerator stopped cooling due to condenser over-heating
Pull refrigerator out to access back, unplug unit and remove the 3 .25" screws cut the power leads to motor and install new with easy to understand instructions provided with new motor. Plug refrigerator back in and enjoy your cold beverages once more. EASIEST REPAIR EVER.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROD from LINCOLN, NE
- Parts Used:
- W11581579
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Two of the parts were broken so the shelf was laying on the drawers so neither could be used effectivly
Pulled out the stud with a wire cutter and replaced it with the exact part you shipped in the kit.
The other 2 parts just slipped on the brackets
Nice thing is now I have extra parts for the other shelf.
The other 2 parts just slipped on the brackets
Nice thing is now I have extra parts for the other shelf.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Berry from APEX, NC
- Parts Used:
- WP2198202
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Therostat needed to be replaced -would not come on again when fridge warmed up
take off the face plate of fridge and follow the cable back to the compartment where fridge and freezer meet. once out, had to remove transluscent cover from thermostat wire - easy and feed that same cover onto the new thermostat. Slow is better and using pliers to force 1/4 to 1/2 inch at a time into the tubing - easier if you have 2 people. After that just put the length back in and insert the controller back in the panel and plug in the electricity again. (to the thermostat). 30 minutes later - cold fridge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Curtis from Sedona, AZ
- Parts Used:
- 833697
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Motor noise while running and clicking when shutting off
The instruction sheet supplied with the new motor described the steps to take very good. Replaced the rubber grommets for the three motor mounts also. A flashlight or light source was needed or was very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gaynell P from Spring, TX
- Parts Used:
- W11581579
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Nonr
Replaced missing stud.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Las Vegas, NV
- Parts Used:
- W11581579
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken shelf supports
Took just a few moments to install. The parts fit like a glove,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Leesburg, VA
- Parts Used:
- 4386774
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set, Wrench (Adjustable)
Both front wheels were severly damaged needing replacement.
I tipped the refrigerator back and my friend used an adjustable wrench to attach put the new wheel assembies on. I also used a socket wrench to get the old attacheement bolts to thread. I rolled the cleaned appliance in place and adjusted the wheels with the socket set for easy door closing. It went smoothly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Jacksonville, FL
- Parts Used:
- WP2198202
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Runaway chilling and thawing - erratic compressor
Synthesized other's comments on similar issues, eliminated those issues NOT applicable. Narrowed what was left and decided on thermostat as first of three likely solutions. Followed other's installation comments and completed a successful replacement. The avaialability of other comments was key to success. Thanks for a great web site. Best clue was the result of slapping the front control panel to start the balking compressor. Not likely to find that in a repair manual.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Belhaven, NC
- Parts Used:
- 833697
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
cooling fan quit
Ordered new fan motor on line took out old motor and replaced with new one
Was this instruction helpful to you?
Thank you for voting!