25348022893 Kenmore Refrigerator - Instructions

replaced the defrosting timer and saved a lot of $ by doing it my self.

pulled down the thermostat cover and unpluged the timer control and replaced it with the new part. total time to repair was about 15 min. there was a vidio on how to replace the new part that just informed me that I did it right!!!!very easy site to find what you are looking for!!!!

Just followed the online instruction video .It was very easy.

Snap Snap job done

When I was moving the refrig. handles from one side to the other...I broke one of the mounts. It was SO easy to order from this place, and they ship IMMEDIATELY. Second time I have used them, and am VERY impressed.

Watched your excellent video online and made the repair just as your technician demonstrated....took about 1 minute!

Unplugged the frig. Removed temp control module from frig, 1 screw with nut driver. Activated defrost timer by rotating adjustment until 2 clicks are heard. Removed two timer mounting screws, unpluged timer, plugged in the new timer, mounted it to the control module with 2 mounting screws. Replaced control module with the 1 mounting screw. Closed door and plugged it up.

You guys at Partselect are the best!!! Went to your site, typed in my appliance symptoms, and received possible fixes. Ordered the suggested parts (under $50) on a Sunday night and got em Tuesday am. Installed the easiest one first and Voila!!!! Frig is working great. Thanks Bob S

Remove 4 screws that hold up overhead controls, this is also the part that holds the light. Unplug the timer and replace. Super simple and runs great now. After you plug it in it may take a few minutes to kick on the compressor but it will. Also I was pleased it was a factory Frigidare part. Price was right.

snapped the wires from frig onto the proper prong and viola,it works. The proper prong is identified by the size because there are two prongs with the wires and two connecting prongs in the socket. I talked to a very helpful representative and she gave me the number for Frigidaire, when I was confused by the placement of the wire. Wish I had remembered her name to share with you. As it turned out I didn't need to call Frigidaire.

I unplugged the refrigerator then removed the temperature adjustment knob from the thermostat which protrudes through the plastic cover located inside the top of the freezer compartment. Then the two hex head retaining screws were removed from the underside of the plastic cover allowing it to drop down and grant access to the bad thermostat control module which was then unplugged and removed from its mounting. The temperature probe is also removed from its sheath at this point as it's attached to the thermostat and has to be removed as well, it simply slides out of the sheath. Installation of the new part is the reverse of the removal of the old part. My refrigerator now works as good as new. Problem solved. The replacement part seemed a little bit pricey for what it is but, in my opinion, was delivered very quickly. As stated by another here, writing this report has taken longer than the repair did.

I watched the video from your company and within a couple of minutes replaced them. Very easy.

Problem not consistent. OK for 2-3 weeks, then freeze coils. Mark and observe the defrost timers manual rotating adjuster. Timer would stop mid cycle. One revolution equals 8 hours of compressor run time followed by 30 minutes of defrost. Replacing timer took 5 minutes.

I followed the procedure online and found the thermostat was ok, it had continuity when cold, and the heater coil was also ok, it too had continuity, therefore the problem was a bad defrost timer. the refrigerator works great, thanks parts select!

I went on partselect put in make and model number, a list showed the probable cause. I watched the how to video. When I received the part in short order I loosened 2 screws disconnected the wiring plug (sprayed it with contact cleaner) pluged it in, removed screws from old part put them in new one. Put timer back in its location and tightened the screws. Very eazy, works fine.