25348022893 Kenmore Refrigerator - Instructions

We replace the end pieces to hook the holder back on the door.

just like the video showed...it was excellent!!!

took 4 screws out of the discharge vent on top of the refrigerator section and unpluged the wiring harness and put the section on the counter and unscrewed the timer and put the new one in and reinstalled the assembly and plugged the Jack and put the 4 screws back in, and rotated the timer and put it on defrost removed the back and check the heaters and drain .

Took a while to get the front off the drawer, but once we did, it slid right into the part you sent and YOU SAVED ME MONEY! Thank you so much!

The instructions given to me by part Select were very good.I replaced the Timer- checked the heater with oham meter it was good- checked the door weather striping it was good and replaced the thermostat with new .So at this point I may need to call a professional unless some one has another solution.

Unplug the refrigerator. Removed the right hand top shelf. Used a 1/4" nutdriver to remove rear center mounting screw for Control Housing. Used Phillips screwdriver to remove two mounting screws for timer. Unplug cable from timer and plug it into the new timer. Install the new timer and re-install the Control Housing. Plug in the refrigerator and adjust the timer to start the unit. This was a snap with the diagnostic provided by Part Select. At first I thought it was the fan rubbing but when I removed the cover (two screws) it was obvious that wasn't the problem. The diagnostic hinted that it was either the timer or the motor capacitor making the noise. Because the noise continued after turning OFF the control, I thought it was the timer...I was right.

Removed the lower trim panel from front of fridg. and loosened two screws enough to turn it about 1/4 inch so the screw heads were in the larger holes. Pulled it out disconnected the wire connector and transfered the heat shield and screws to the new clock, connected the wire connector and aligned the screws. tightened them and job done. Has worked like new sense. Thanks Roger

Purchased switch and socket, not sure which had failed. Moved all frozen food to refrigerator, turned off breaker. Used nutdriver to remove two screws holding box containing switch and socket. Removed old switch and socket. Removal was slightly difficult since cabling came off both sides of the box. Installed new switch and socket and bulb. Turned breaker back on, checked light as workiing. Replaced scrrews to re-intstall switch box ( or whatever you call it ) Closed door and waited for freezer to cool. Returned all frozen food to freezer. Job Done

I ordered the part, easily installed a new one. Everything works greatnow.

Ordered the new part-Unplugged the refrigerator - took off the cover over the defective timer - put in the new part put the cover back on - plugged the refrigerator back in - so far, so good!~

I watched the video you had on-line and it was simple. Thank you so much

You guys at Partselect are the best!!! Went to your site, typed in my appliance symptoms, and received possible fixes. Ordered the suggested parts (under $50) on a Sunday night and got em Tuesday am. Installed the easiest one first and Voila!!!! Frig is working great. Thanks Bob S

Remove 4 screws that hold up overhead controls, this is also the part that holds the light. Unplug the timer and replace. Super simple and runs great now. After you plug it in it may take a few minutes to kick on the compressor but it will. Also I was pleased it was a factory Frigidare part. Price was right.

snapped the wires from frig onto the proper prong and viola,it works. The proper prong is identified by the size because there are two prongs with the wires and two connecting prongs in the socket. I talked to a very helpful representative and she gave me the number for Frigidaire, when I was confused by the placement of the wire. Wish I had remembered her name to share with you. As it turned out I didn't need to call Frigidaire.

I unplugged the refrigerator then removed the temperature adjustment knob from the thermostat which protrudes through the plastic cover located inside the top of the freezer compartment. Then the two hex head retaining screws were removed from the underside of the plastic cover allowing it to drop down and grant access to the bad thermostat control module which was then unplugged and removed from its mounting. The temperature probe is also removed from its sheath at this point as it's attached to the thermostat and has to be removed as well, it simply slides out of the sheath. Installation of the new part is the reverse of the removal of the old part. My refrigerator now works as good as new. Problem solved. The replacement part seemed a little bit pricey for what it is but, in my opinion, was delivered very quickly. As stated by another here, writing this report has taken longer than the repair did.