Models > 25331430101 > Instructions

25331430101 Kenmore Refrigerator - Instructions

Jump to:

All Instructions for the 25331430101
61 - 75 of 216
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Linda from BOZEMAN, MT
Parts Used:
240505801
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Light Switch too loose so no longer triggered by the door.
Googled it on Youtube - unplugged the fridge, used a paint scraper to loosen the old light switch, unplugged it from the electrical source, connected the new switch, replaced the whole unit into the proper location and pushed it firmly into place.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from ORMOND BEACH, FL
Parts Used:
240505801
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Light Switch not working properly
After unplugging the fridge, I took a small flat headed screwdriver and carefully pried off the light switch from the inside, right side of the refrigerator. I disconnected the 2 wires from the switch and replaced it with the new switch and pushed it back into the frame of the fridge. Done !! Very very easy !! Thank you
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sherry from Newberry, SC
Parts Used:
5303918202
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
the freezer frosted up and the fridge was not getting cold.
I watched the instructional video and did what it said.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Martin from N HOLLYWOOD, CA
Parts Used:
5303918774
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
Fan was off kilter and began rubbing the frame which is caused it to slow down and make an disturbing audible noise.
Before buying the part, I watched your video and realized it was extremely simple to remove and replace. Item was to take 7-10 days and I received it in 4. Took longer than 15 minutes because I had to move the fridge forward, get my tools and a vacuum, get a cup of coffee and get to it. Very easy and the video was exactly step by step. It took longer to vacuum all of the dust bunnies than to replace the part.

Honestly, I was in the market to buy a new refrigerator but now I believe I'll wait several more years. Thank you for your support.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bill from STERLING, VA
Parts Used:
5303918774
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Socket set
Condenser motor burned out
I followed the instructions on your website, made it a simple as possible. Very tight work area sometimes fingers only, but a little patience works.
Saved at least $300. By not paying a repair person.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Judy from ROYSE CITY, TX
Parts Used:
5304464438
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Freezer wasn't cooling - compressor not engaging
Ordered the Capacitor and the Thermostat Control. Parts were received in a matter of a few days, easy to install, but did not fix the problem. Had to call a repairman to fix the problem (compressor relay - this part not available to order for this model number with Parts Select). Will continue to use Parts Select in the future for other parts, but not happy that the actual part I needed was not available - had to use other methods.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jeffery from Phillipsburg, NJ
Parts Used:
218396700
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
the refrig was in storage for about a year, the freezer door warped
removed freezer door and installed the new one. This was a pretty easy thing to do, although putting the old handle on the new door was a challenge. No knowing that there is a plastic piece holding the top of the handle i broke the that piece and had to order another one. Mean while the freezer was making alot of frost inside, so that had to be cleaned after the new part came.
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
cheryl from hammond, NY
Parts Used:
240331401, 240311502, 240311501
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
all 3 refrigerator door retainer bar were broken
I had to cut the replacement bars to the correct length. But everything else was easy. The quality of the repacement bars is much better than the originals. Thanks!
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Christine from Bourne, MA
Parts Used:
240311502, 240311501
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
relaced shelves
Removed old , assembled and popped in new.Perfect!
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Holly from Magna, UT
Parts Used:
240311502
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Door shelf broken
snapped shelf end cap in place, now my wine bottles don't fall on the floor when you open the fridge door!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Deborah from Warren, MI
Parts Used:
240311501
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
I was missing the bar and end caps for the bottom shelf
I purchased a left and right end cap and the bar but I ended up with 2 right end caps of different sizes. Partselect happily accepted my return and shipped the correct part. I hadn't had a bottom condiment shelf for over 4 years. It's nice to have one now. It was easy. Just popped on one end cap, slid the bar on, slid on the other end cap (had to force a little) and popped on that end cap. Voila! new shelf.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Francine from Port Charlotte, FL
Parts Used:
240311502
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Broken shelf retainer end
I just slid the end of the cap on the end. REAL EASY...Now I can use my shelf again.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Austin, TX
Parts Used:
240311501
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
The end cap for the lower door shelf broke
Removed the broken end cap piece from the shelf retainer bar. You need to pry up the little metal tabs with a screwdriver to remove the end cap, then slide in the new one and crimp down the tabs with the pliers. super easy. Replacement part was identical so it fit perfectly.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Brad from STOCKTON, CA
Parts Used:
5303918549
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Refrigerator wasn't getting cold
removed the back panel of the freezer and unplugged the connector for the Motor. Removed the air diffuser, then removed the fan blade. Removed the 2 screws holding the motor to the bracket. Disconnected the old wire harness and installed the new one. Put the fan blade onto the new motor and installed the motor onto the bracket. Put the air diffuser back on, plugged the motor back in and fastened the back panel. Plugged the refrigerator into the outlet and tested, OK!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from MONTGOMERY, IL
Parts Used:
5303918202
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
Coils frozen over. Refrigerator not cooling
I cut wires from bad thermostat and removed it . Stripped wires and crimped connectors on new thermostat and wires from old thermostat. Used heat gun to seal sleeves over connectors. Very helpful video from this site Thanks, you will be my go to parts supplier from now on!!!!!!!!!!!!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 25331430101
61 - 75 of 216