1068652610 Kenmore Refrigerator - Instructions

****Make are you order Capacitor & Starter relay too (we ordered separtely so had to pay shipping twice)**** Super easy just open access panel on back near compressor and remove retention clip with fingers, remove & replace both capacitor & starter, put clip and access panel back on, plug in and allow 8 hours to cool! Works like new again! Hope it goes another 10 years

My fridge did not have icemaker add on. The evap fan is in the freezer behind the back panel. Empty the freezer section (into a cooler) and turn the fridge off. Remove all the shelves in freezer section. Remove the shelf support tabs by lifting them up. use phillips head screwdiver to remove back panel in freezer section. Use nut driver to remove fan shroud. Remove old fan and save the mounting arms. Install mounting arms on new fan and install fan. Install shroud, back panel, shelf mounts and shelves. Thats it!

Just moved into a new rental home and a few days in the bar that holds all the stuff -- milk containers, juice jugs, etc. -- in the refridge door falls off. The old tenants had "fixed" it with tape on one side and paint stirrers and caulk on the other side. (No kidding -- a real overkill job they did).

I looked up the model number online and found this site and promptly ordered the parts for $6 plus shipping. The parts came and snapped right in perfectly. Took only a minute.

I really only had to use pliers to pull out the oodles of hard swirly caulk from the slots in the door left from the overkill job by the previous tenants.

PartsSelect is awesome! The site makes it easy to look for the part you want and the parts were perfect -- No more stuff falling out the fridge door.

PS. This form made me select the age of the appliance. I really have no idea since I just moved in and it was already here.

Ordered the wrong shelf, returned it and ordered the correct shelf. Placed it on the frame. Service was two days.

Went online with the model number, the part was very easy to find, diagrams helped me to have confidence in the choice. Parts came in two days, tore them open and used a screw driver to replace the broken shelf brackets, replaced shelves, I am a happy camper!!

Slid the end caps onto the shelf, placed the tape on the pieces as noted in the directions, and put the shelf back in place. Fast service, exact part, easy to find on the web site! Great!

First I removed all the screws from the back cover.
2nd removed fan nut and fan blade
3rd removed fan bracket
4th I traced wire to the condenser and disconnected wires from wire nuts.
Installed existing fan brackets to new motor kit
then reconnected wire nuts to new motor cord
Reinstalled fan nut and blade,
reinstalled cover, plugged it in and BAM .WORKS PERF!

figured out the condenser fan was kaput. Tried WD, worked for several days then gave out completely. Took off back of fridge and trained small fan on compressor while I ordered new condenser fan. The swap was easy, undid the housing bolts, stripped off the connector, reconnected and voila! works perfect.

Unplug fridge, unpluged fan motor from plug socket, removed bracket screws, removed fan retainer clip from shaft. removed screws holding fan to bracket

Simply took broken pieces of old stud out and replaced with the new ones. Used pliers to adjust them. Replace a freezer stud and a fridge stud.

I removed 7 screws hold the heavy cardboard cover on the rear of the fridge. The dificult part was taking the screws that hold the 3 fan motor braces on the fan out. After that it was a matter of making the wire conections and putting it back in. I did not have enough room to laydown to do the work, If i had it would have been a lot easier to see the screws that had to be removed. All in all an easy job, and the part was a perfect fit.

Very easy. Left the front of the refrigerator so it is approx. 4 inches of the floor. (used a two by four. Removed the screws (one for each roller). Removed the rollers and replaced with new rollers. Reinstalled the screws with secures the rollers to the refrigerator. Done

Followed instructions from ideoo

Removed door and replaced bushing bracket was ok.

Reviewed Youtube video as a reference. Unplugged refrigerator. Removed old defrost timer. Matched the color of the wiring harness to the diagram that came with the part. Attach new part to wiring harness.