36348047891 Kenmore Refrigerator - Instructions

Removed door off hinge , remove bottom hinge, drill out rivet, lift off old cam & replace with new cam ,add new 1/4' BOLT(NOT SUPPLIED) to location where rivet was, reinstall bottom hinge & door ,check alignment, works perfect.

Thanks

Placed blocks under the refrigerator door to take weight off the lower hinge pin. Removed the hinge by removing two screws into the refrigerator and two screws into the bottom of the door itself. This allows the hinge to be removed so the old nylon "closer" pieces can be removed (the one attached to the refrigerator has a rivet holding it in place so that has to be drilled out and replaced with a 3/16 inch bolt and nut). After re-attaching the nylon "closer" to the refrigerator side of the hinge and placing all the shims back in place, I re-attached the hinge to the door first, then the half hinge to the refrigerator. Had to line up the holes, tighten the screws and presto, the door closes like it was new again.

The freezer door side is more difficult as there are wires and a water line to work around.

BUY TWO CAMS! Just like the others, both of the cams were shot. My husband & I did this ourselves & have NEVER attempted appliance repair before.
We propped the door up high enough to access the bottom hinge piece on the fridge & removed using socket. Removed the cover from the top hinge. Slid door down off the top hinge in able to get to the cam on bottom of door. Replaced this cam 1st in order to get door back on while worked to get the old cam off hinge. As others posted, this is rivited on. Used grinder to grind off rivit & hammer & punch to punch out. Attached new cam with bolt & nut found in our tin of leftovers. Inserted hinge into door & reattached to fridge. DONE! Not hard at all & didn't even argue the whole time.

At first, I noticed the refrigerator door didn't close at the same level of the freezer door. I started to adjust the hinges and noticed a chewed up black 'washer' at the base of the door hinge. Ppartselect.com was awesome, in that I easily found the schematic of my fridge, and the part I needed. Ordering was a snap, and it came to the house pretty quickly.
Installation, first raise the door up as high as you can, then scotch it with wood blocks (closed door). This takes the pressure off the bottom hinge you must remove.
Taking the hinge off is a snap, but then the problem presented itself. The old door closing cam was riveted to the hinge. I couldn’t get the old one off! I ended up taking it to the garage and breaking out the Dremmel tool with the abrasive cutter (the one that will cut through nails. I ended up cutting off the rivet. This was a pain.
I then found a small nut/bolt and put the new piece on, then put it back into place and removed the blocks. Works good as new. The toughest part by far was getting the old cam off… but there may be some easier way to get the rivet out that I’m not aware of.
Good luck.

Part was perfect fit .Removed fan .three screws.replaced that s it

Removed icemaker from freezer,
Removed 3 screws from cover plate, and removed screw securing main gear, removed gear.
Pulled back cover plate to expose switches and mechanism.
Removed screw holding switch to remove switch, and installed new switch.
I should have taken a pic of the cover plate, the interior mechanism and the wiring as I went along. It would have saved me 45 minutes in reassembly. Also, as luck would have it, I reversed the wiring on the switch. So off was on, and I had to remove it, switch wires and re-install.
But it works!

Separately (from a different site) purchased new compressor fan and motor. I purchased the grommets here because the other site listed the grommets as temporarily out of stock. I did watch one of the videos on PartSelect about the grommet replacement. Repair was pretty simple, biggest challenge was getting to the screw on the far side of the motor. Removed the two screws holding the fan motor into place. Removed motor and blade. Reinstalled with new fan blade, new grommet and new motor.

This was a 15 year old great working GE regrigerator. Refrigerator was not cooling properly, though the freezer worked great. Using flashlight, examined cam riser which was clearly broken. YOU MUST ORDER TWO GASKETS AS BOTH WILL BE WORN. After removing all food from the door, taped plastic sheet over the open space to keep food somewhat cool Removed top hinge cover and screws on top of door and lifted door out of bottom bracket placing it flat on kitchen island. Unscrewed hinge elements including old broken cam and shims form the bottom of the door and fit in the new cam. Unfortunately one of the shims was broken, so I used a thin plastic black washer from the hardware store which was big enough to fit over the pin on the bottom of the refrigerator itself. Screwed all the parts back together. Be VERY careful to note how you removed them in the first place...mabe take a digital foto or two. This was kind of tricky to remember. Then used a hammer and chisel to break off the rivit holding the bottom hinge elements on the refrigerator. Sawing with jigsaw didn't work that well. The rivit came right off. Then used a flat head screw, lock washer and nut instead of a reivit and attached the new second cam riser. You are now done with the new parts. Simply reattached the door and it closed like new. Had a simultaneoius problem with a faulty defrost heater in the freezer which also had to be replaced and which was really easy to do. About an hour max. This was the real cause of the refrigerator not cooling properly. But that's another story.

Had to defrost the freezer to melt off all the ice before servicing. Once that was done the icemaker replacement only took about 15-30 minutes to complete. The new icemaker came with many accessories and adaptors that were not needed and the instructions were based on replacing an older model and not really clear for my model. They mentioned not being able to use the new stripper but it was exactly the same as the old one so I left the new one in place. All in all it was easy and did the job.

I didn’t do the repair because I ordered two grommets. When they arrived, one of the packages was empty! Instead of just sending me another one, they refunded the part so I still need one. By the way, I was not refunded half the shipping either which was more than the part itself.

Remove the one screw holding the unit in place, unplug it, slide in the replacement, plug and screw it in.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Like the rest of the other statements it was easy with 2 2X4 pieces of wood to block the door up. The other suggestion about buying two of the pieces was a good idea. Once I took off both the top and bottom pieces they were both worn out and it was easy to replace them both at the same time. The door is working good again and shuts on its own.

Removed four screws at bottom of door, while someone held the door in place replaced the upper cam (there are two) applied some silicone plumbers lube between the mating surfaces and tightened it up. Works like new bottom cam was only slightly worn. P.S. Remove everything from the door first.

First a big thank you to PartSelect.com. I read the stories posted by others before ordering the parts and found out that I probably needed 2 of these cams. So I followed the advice of others and ordered 2 cams. I'm really glad I did because once I got the door off I discovered both were broken up real bad. Maybe you guys should think about offering them as a set?
Anyway the repair was fairly easy, except for the bottom cam which was revited to the bottom bracket. Again, thanks to the other stories about repairs with this part I was already expecting this. So the repair went like this. I removed the door by unscrewing the hinge on top(1 screw and 2 bolts). Took the door off and laid it on its side. Removed the bottom bracket( 2 bolts). Used a drill to drill out the rivit. Used a spare screw/nut that I had in a tool box to fasten the cam to the bracket. Put it all back together and I was done. The biggest challenge was figuring our if I needed 2 cams,so with the advice of others on your site, my repair was a snap.